Skip to main content
Bel Covo
modern sleek onyx polished concrete

Concrete contractor in Gentry, AR

What does concrete flooring cost in Gentry, Arkansas?

Concrete flooring in Gentry runs the same ranges as the broader Arkansas market: polished concrete lands in the low-to-mid single digits per square foot, stained and decorative systems fall in the middle, and high-end epoxy or metallic builds reach the top of the range. Slab condition, square footage, and finish selection all move the real number. The regional breakdown below walks through what actually drives a Gentry quote up or down.

Concrete work in Gentry

Gentry sits at the western edge of Benton County in Northwest Arkansas (NWA), about 32 miles northwest of our NW Arkansas team. As a concrete contractor in Gentry, AR, we pour driveways and shop slabs, coat garage floors, and polish concrete floors. When we pour a slab that will get a coating or a polish, we write the pour spec for that finish.

A large bakery plant gives Gentry an industrial side. So along with driveways and home garage coatings, Gentry sends us a steady run of shop slab and warehouse flatwork requests, more than a town that’s all homes. Get your price now.

What does concrete work in Gentry actually involve?

Concrete work in Gentry starts before the quote. Our NW Arkansas team looks at what the slab is for, how wet it gets, what it has to carry, and when the finish goes on. That sets the order the crew works in.

New concrete pours

Driveways and approaches. Gentry driveways sit on Boone Formation cherty clay, the clay and chert left behind where limestone weathered in place. It drains slowly and shifts under load in wet spells. So before we pour, we pack the subgrade and proof-roll it, which means driving a loaded truck over it to find soft spots. Our driveway quote is a 5 inch slab on a packed gravel base, with rebar, poured with a 4500 PSI mix. We saw the control joints at a spacing set by the slab’s thickness. Driveway details.

Shop and barn slabs. Working buildings around Gentry carry heavier loads than a home slab, and they often get a coating or polish later. So we thicken the edges under overhead doors, build in steel, and put a vapor barrier under any slab that will get a finish later. Shop slab details.

Patios and flatwork. Benton County’s wet winters put real freeze-thaw stress on outdoor slabs. Control joints sized to the slab’s thickness are our standard practice, not an upsell. Patio details.

Concrete flooring: coating and polishing

Garage floor coatings. We diamond-grind the slab to open it up, then lay the coating. Home garages usually get our RESA Flake floor, a resinous floor coating with color flake broadcast into it. Shops do better with a polyaspartic that holds up to fuel, oil, and rolling loads. Garage floor coatings.

Polished concrete. For a Gentry barndominium or shop that needs a tough finished floor without tile or carpet, we polish the slab itself instead of putting a topcoat on it. The chert in Boone rock gives a polished floor here a warm salt-and-pepper look you see across this region. Polished concrete details.

Pour-4-Polish: one spec for the pour and the finish

Pouring a new slab in Gentry that you plan to coat or polish? There's no reason to hire two contractors. We write the pour spec for the finish, so the mix and the cure suit what goes on top. You get one contact for the whole job and one workmanship warranty on the completed install.

What stone and aggregate goes into Gentry concrete?

Crushed Boone limestone from APAC-Central / McClinton-Anchor - Gravette Quarry, on Hwy 72 east of Gravette, supplies the rock for this corner of Benton County. Boone limestone polishes to a warm cream color with chert in it. The chert is porous, so it shows as lighter freckles on stained and polished floors. That’s normal for this region, not a flaw.

But it does change the spec. Those chert lumps can react with the alkali in cement. That reaction is called alkali-silica reaction. Over time that can leave a web of fine cracks, called map cracking. So on any high-spec polish or stained floor, we spec low-alkali cement and Class F fly ash to stop it. Under the slab, the cherty clay over the Boone drains slowly. That’s why packing and proof-rolling come first on a Gentry pour.

See what your Gentry project costs online

Answer a few questions about your project and get a price. The drive cost from our NW Arkansas team is already in it.

How much does concrete work cost in Gentry?

Driveways and flatwork in Gentry run $6.96 to $16.43 a square foot, depending on thickness, rebar, and finish. A garage floor coating runs $8.55 to $10.39 a square foot, and polished concrete starts at $3.58 a square foot. The ranges above include setup. A single rate can sit a little under them. The drive cost from our NW Arkansas team is figured into every quote. It spreads across the whole job, so a bigger job carries less travel cost per foot. The online quote tool gives you a number without a callback.

Which other Benton County cities does Bel Covo serve?

Our NW Arkansas team also covers Siloam Springs, Gravette, Centerton, Bentonville, and the rest of Benton County. The Arkansas service area page has the full 2026 list. Use it to compare nearby city pages and see how the drive cost grows across the county.

What the concrete in Arkansas is actually made of

The aggregate story in Arkansas concrete

Arkansas has two kinds of concrete rock, and a polished floor shows which one you got. The northwest Ozarks run on Boone Formation limestone, with 15-30% chert in some Benton County pits. The Delta runs on Mississippi River gravel. The two floors differ so much in color, texture, and how they take a finish that they might as well be in two states.

Northwest cities we cover, like Fayetteville and Fort Smith, are on the Arkansas concrete flooring hub.

What aggregate drives northwest Arkansas polished floors?

Northwest Arkansas runs on Boone Formation limestone (Mississippian age). That stone carries a lot of chert, a hard rock made of silica. Crushed Boone stone goes into structural concrete. Most metro mixes get their sand and gravel from river bars in the White River drainage. Sandstone from the Atoka and Bloyd formations shows up too, but only as a second source in some rural Benton and Carroll County pours.

Polished, these floors read as a light warm gray with a cream-to-bone tint. Off-white and buff-tan chert spots break it up. How many spots you get depends on which pit the ready-mix plant pulled from on pour day. At our standard cut, the floor shows a salt-and-pepper look. Cut deeper, to medium or full aggregate exposure, and it turns into a mottled field with bits of fossil in it. Fossil crinoid stems, the Boone’s best-known mark, show up as small pale disks.

Why does Boone chert leave pinholes in a polished floor?

Porous chert is the headache. The Boone holds lumps of chert, and some are full of tiny holes while some aren’t. Arkansas Geological Survey papers name them as a cause of past quarry problems. In a polished floor, that porous chert grinds faster than the stone around it. That leaves pinholes, dull spots, or pop-outs at the surface, and no amount of densifier fixes them after the fact.

Northwest Arkansas aggregate suppliers include the APAC-Central McClinton-Anchor quarries in Springdale, Hindsville, and Gravette. APAC Valley Springs in Harrison is a second supplier.

Boone stone polishes bright. Acid stains take well on it in earth tones and warm grays. Chert-heavy mixes take stain in patches, because silica doesn’t react with the stain, so a stained floor shows the chert as light freckles on darker stone. Broom finishes look clean and gray. Exposed-aggregate finishes look good here, since you can see both the fossils and the chert.

How does Delta gravel change what a polished floor looks like?

The Delta runs on sand and gravel the Mississippi River laid down, and the coarse rock in it is mostly chert and quartz pebbles. There’s some sandstone, novaculite, and milky vein quartz mixed in, all worn down from older Paleozoic bedrock upstream. There’s next to no local limestone quarry. So crushed stone for the main mixes gets hauled in from Batesville (Independence County) and the Little Rock quarry belt. For jobs in eastern Crittenden County, it comes from Memphis-area plants.

Polished, these floors read warm tan to buff. Cut to the stone, you see creamy cement paste broken up by round chert pebbles from pea-size to marble-size. They come in white, amber, honey, and gray, and now and then you get a rose-red jasper. The whole floor looks warmer and busier than a crushed-limestone floor from northwest Arkansas or southwest Missouri.

What does Delta gravel mean for cracking, stain, and finish?

Round river gravel leaves pebble outlines you can see at a medium or full cut. Some clients love that look. Others call it busy. Some beds of chert-heavy river gravel can also cause alkali-silica reaction, or ASR. That’s when silica in the rock reacts with the cement and swells, which leads to map cracks and pop-outs. Good Delta ready-mix plants guard against it with Class F fly ash. A slab poured with imported rock of unknown origin still carries ASR risk. Still, the expansive clay under Delta slabs is a bigger risk than the rock.

Delta aggregate and ready-mix suppliers include Arkansas Concrete Company, with plants in Forrest City, Wynne, Brinkley, Marianna, and Helena. Others are Razorback Concrete Company (West Memphis, with more than 15 plants), and Forrest City Ready-Mixed Concrete Co.

At a medium cut, a polished Delta-gravel slab has a lot of life. Round pebbles catch light in a way sharp crushed stone doesn’t. Stain goes on in patches. The cement paste takes acid stain fine, but chert pebbles don’t, so the stain makes the contrast stronger. Broom finishes look fairly clean, since the fine sand is rich in quartz. For an even color without the native gravel, the usual Delta choices are epoxy coating over a prepped slab, a self-leveling overlay, or grind-and-seal.

What Does Concrete Work in Gentry Look Like?

Polished concrete floor in luxury home entryway reflecting chandelier and modern interior designAction Powersports custom logo embedded in glossy black epoxy showroom floorRound Barn polished concrete floor with mirror-like reflections of windows in dark high-gloss finishPolished charcoal concrete floors in open-plan luxury home with stone fireplace and floating staircasePolished dark concrete floor in restaurant bar area with branded bar stools, tap handles and TVsMetallic epoxy floor in dark amber and brown marble swirl pattern with mirror-like gloss finishMetallic epoxy floor with colorful light-ray inlays at Brady Theatre in performing arts venueExpansive sealed concrete floor in double-height residential great room with French doors and transom windowsLow-angle dramatic view of polished concrete floor in large warehouse with column reflectionsQuarter-sawn wood-plank concrete overlay detail showing realistic grain texture and warm tonesHigh-gloss sealed outdoor concrete slab with mirror-like reflection of a boat trailer in daytimePolished concrete floor in Westmoore Community Church lobby viewed from wider angle

How far will Bel Covo travel to pour concrete in Gentry?

Bel Covo serves Gentry concrete projects within the standard service radius, and our crews are typically 3-6 weeks booked at any given moment. Every quote is itemized to show the cost of each step of the work, including the mobilization that gets equipment on site, so the quote doubles as the order of operations for your project. On accepted work, billing follows those same steps and shows the completion percentage of each as it happens, with nothing buried in a vague lump sum. Call 479-397-3406 for a straight answer in under two minutes.

Which concrete services does Bel Covo offer in Gentry?

Our Gentry crews handle polished concrete, epoxy and polyaspartic coatings, decorative staining, driveways, patios, and repair work. Every job follows the same Pour-4-Polish process and finish discipline used on our flagship projects. The related links below point to the specific service pages that match common Gentry requests.

What questions come up most about Gentry concrete?

Does Bel Covo serve Gentry directly?

Yes. Gentry is inside our NW Arkansas coverage area, about 32 miles northwest of our NW Arkansas team. We pour driveways and shop slabs, coat garage floors, and polish concrete across Benton County. The drive cost, our trip to your site, is its own line on every quote, so you see it before you commit.

What does a concrete driveway cost in Gentry?

Our driveways run $6.96 to $16.43 a square foot, depending on thickness, rebar, and finish. A two-car driveway of about 500 square feet runs $3,650 to $8,650 before the drive cost. A small floor runs above the per-foot range, since setup spreads over fewer feet. The online quote tool gives you your own number in about 2 minutes.

Can you pour and coat a garage floor in the same scope?

Yes. Under our Pour-4-Polish spec, we write the pour for the floor that goes on it: the mix, the cure, and how long the slab dries before the coating goes down. The pour and the coating run on one schedule.

Do you pour industrial shop slabs and warehouse flatwork in Gentry?

Yes. Gentry has an industrial side, so heavy shop slabs and warehouse flatwork come up here along with home jobs. Our NW Arkansas team handles both sizes of work.

Last updated:

Ready to transform your floor?

Get a free, no-obligation quote for your project.

Benton County, Arkansas

See concrete work across Benton County, Arkansas →