Skip to main content
Bel Covo
modern sleek onyx polished concrete

Concrete contractor in McCrory, AR

What does concrete flooring cost in McCrory, Arkansas?

Concrete flooring in McCrory runs the same ranges as the broader Arkansas market: polished concrete lands in the low-to-mid single digits per square foot, stained and decorative systems fall in the middle, and high-end epoxy or metallic builds reach the top of the range. Slab condition, square footage, and finish selection all move the real number. The regional breakdown below walks through what actually drives a McCrory quote up or down.

A railroad town built on Delta clay

As a concrete contractor in McCrory, AR, we pour on deep clay laid down by the White and Cache rivers. McCrory is a railroad town on US-64 in Woodruff County, about 37 miles northwest of our Eastern Arkansas team. New concrete here runs $5.32 to $15.61 a square foot, and garage floor coatings run $8.55 to $10.39.

Row crops drive the county economy. So most jobs here are working slabs: an ag-storage pad, a detached farm shop, or a driveway on a rural lot, not a suburban garage makeover.

What does McCrory’s Delta soil mean for a slab?

The ground under Woodruff County is deep alluvial clay, laid down by the White and Cache rivers over thousands of years of floods across the Delta. It’s expansive soil. It soaks up water and swells, then dries out and shrinks. Pour a slab on loose or soaked clay and the slab moves right along with it. Once it moves, the control joints open up and cracks run along the rebar lines. Any coating or polish on top starts to peel.

So we pack the base first. The mix is at least 4,000 PSI (PSI is how much weight the cured concrete holds per square inch). On any slab that will get a coating or a polish, a vapor barrier goes down before the concrete does. Without it, moisture coming up through the clay lifts the finish from below, usually within two years.

Which gravel goes into a McCrory slab, and how does it polish?

The ready-mix for McCrory jobs comes from the Arkansas Concrete Company - Wynne Plant in Cross County. Its Delta river gravel makes a warm tan mix. When we grind and polish that slab, the gravel shows up as a speckle of white, amber, and honey-colored pebbles. That gives an inside floor some depth without paying for a fancy decorative system.

The Wynne plant sells the ready-mix, and with polished concrete, we grind, harden, and polish the slab it makes until the slab itself is the floor. On a shop or barndominium floor, it runs $3.83 to $6.25 a square foot. There’s no coating on top to peel.

Vapor barrier is standard on Delta ground

Woodruff County's river clay holds moisture all year. Any slab you plan to coat or polish needs a vapor barrier under it before the pour. If an older slab went down without one, a moisture test tells us whether it needs a self-leveling overlay first or can take a coating directly.

What does concrete work cost in McCrory?

Driveways run $6.96 to $16.43 a square foot. A two-car driveway of about 500 square feet runs $3,650 to $8,650 before travel to your site. A drive that small runs above the per-foot range, since setup spreads over fewer feet. Shop slabs sit near the top of the flatwork range. They need thickened edges under the overhead doors and heavier steel.

A single-car garage coating runs $8.55 to $10.39 a square foot.

Need a new slab and a finished floor both? With Pour-4-Polish, we write the pour spec for the finish that goes on it. You get one mobilization on the quote and one warranty on the workmanship for the whole job. The online tool shows the trip from our Eastern Arkansas team as its own line before you commit.

Which floor fits your building?

  • A farm shop or ag-storage slab that stays bare: a new pour on a well-packed base.
  • A shop or barndominium floor you want finished for good: polished concrete, ground into the slab itself.
  • A garage that sees oil, chemicals, and hot tires: a flake or polyaspartic system, picked for the traffic and chemicals that floor will see.

What concrete work do we handle in Woodruff County?

Farm and ag-storage slabs fill most of the schedule. Commercial flatwork and driveways fill the gaps in mid-season. And coating and polishing jobs on existing slabs run all year, on days too wet to pour outside.

  • Driveways. Our standard concrete driveway quote is a 5-inch slab on a packed gravel base, with #4 rebar and a 4500 PSI mix. On anybody’s bid, check for at least 4 inches and 4,000 PSI. We time the saw-cut control joints and cut them to match the slab’s thickness. This clay shifts a lot in a dry summer. A joint cut too shallow cracks again on the first hot stretch.
  • Shop and barndominium slabs. Shop slabs get thickened edges where the equipment doors land, and at least 5 inches of depth under any heavy machine.
  • Patios. Patios and other outside flatwork get the same base prep as a driveway.
  • Garage coatings. Garage floor coatings start with diamond grinding to the right CSP profile, the surface roughness a coating needs to grip.

See what your McCrory floor costs

Enter your square footage and address, and get a detailed price in about 2 minutes.

Nearby Eastern Arkansas cities we also serve

Our Eastern Arkansas coverage runs the length of US-64 and the Delta towns around it. The Arkansas service area page has the full map.

What the concrete in Arkansas is actually made of

The aggregate story in Arkansas concrete

Arkansas has two kinds of concrete rock, and a polished floor shows which one you got. The northwest Ozarks run on Boone Formation limestone, with 15-30% chert in some Benton County pits. The Delta runs on Mississippi River gravel. The two floors differ so much in color, texture, and how they take a finish that they might as well be in two states.

Northwest cities we cover, like Fayetteville and Fort Smith, are on the Arkansas concrete flooring hub.

What aggregate drives northwest Arkansas polished floors?

Northwest Arkansas runs on Boone Formation limestone (Mississippian age). That stone carries a lot of chert, a hard rock made of silica. Crushed Boone stone goes into structural concrete. Most metro mixes get their sand and gravel from river bars in the White River drainage. Sandstone from the Atoka and Bloyd formations shows up too, but only as a second source in some rural Benton and Carroll County pours.

Polished, these floors read as a light warm gray with a cream-to-bone tint. Off-white and buff-tan chert spots break it up. How many spots you get depends on which pit the ready-mix plant pulled from on pour day. At our standard cut, the floor shows a salt-and-pepper look. Cut deeper, to medium or full aggregate exposure, and it turns into a mottled field with bits of fossil in it. Fossil crinoid stems, the Boone’s best-known mark, show up as small pale disks.

Why does Boone chert leave pinholes in a polished floor?

Porous chert is the headache. The Boone holds lumps of chert, and some are full of tiny holes while some aren’t. Arkansas Geological Survey papers name them as a cause of past quarry problems. In a polished floor, that porous chert grinds faster than the stone around it. That leaves pinholes, dull spots, or pop-outs at the surface, and no amount of densifier fixes them after the fact.

Northwest Arkansas aggregate suppliers include the APAC-Central McClinton-Anchor quarries in Springdale, Hindsville, and Gravette. APAC Valley Springs in Harrison is a second supplier.

Boone stone polishes bright. Acid stains take well on it in earth tones and warm grays. Chert-heavy mixes take stain in patches, because silica doesn’t react with the stain, so a stained floor shows the chert as light freckles on darker stone. Broom finishes look clean and gray. Exposed-aggregate finishes look good here, since you can see both the fossils and the chert.

How does Delta gravel change what a polished floor looks like?

The Delta runs on sand and gravel the Mississippi River laid down, and the coarse rock in it is mostly chert and quartz pebbles. There’s some sandstone, novaculite, and milky vein quartz mixed in, all worn down from older Paleozoic bedrock upstream. There’s next to no local limestone quarry. So crushed stone for the main mixes gets hauled in from Batesville (Independence County) and the Little Rock quarry belt. For jobs in eastern Crittenden County, it comes from Memphis-area plants.

Polished, these floors read warm tan to buff. Cut to the stone, you see creamy cement paste broken up by round chert pebbles from pea-size to marble-size. They come in white, amber, honey, and gray, and now and then you get a rose-red jasper. The whole floor looks warmer and busier than a crushed-limestone floor from northwest Arkansas or southwest Missouri.

What does Delta gravel mean for cracking, stain, and finish?

Round river gravel leaves pebble outlines you can see at a medium or full cut. Some clients love that look. Others call it busy. Some beds of chert-heavy river gravel can also cause alkali-silica reaction, or ASR. That’s when silica in the rock reacts with the cement and swells, which leads to map cracks and pop-outs. Good Delta ready-mix plants guard against it with Class F fly ash. A slab poured with imported rock of unknown origin still carries ASR risk. Still, the expansive clay under Delta slabs is a bigger risk than the rock.

Delta aggregate and ready-mix suppliers include Arkansas Concrete Company, with plants in Forrest City, Wynne, Brinkley, Marianna, and Helena. Others are Razorback Concrete Company (West Memphis, with more than 15 plants), and Forrest City Ready-Mixed Concrete Co.

At a medium cut, a polished Delta-gravel slab has a lot of life. Round pebbles catch light in a way sharp crushed stone doesn’t. Stain goes on in patches. The cement paste takes acid stain fine, but chert pebbles don’t, so the stain makes the contrast stronger. Broom finishes look fairly clean, since the fine sand is rich in quartz. For an even color without the native gravel, the usual Delta choices are epoxy coating over a prepped slab, a self-leveling overlay, or grind-and-seal.

What Does Concrete Work in McCrory Look Like?

Polished concrete floor in luxury home entryway reflecting chandelier and modern interior designAction Powersports custom logo embedded in glossy black epoxy showroom floorRound Barn polished concrete floor with mirror-like reflections of windows in dark high-gloss finishPolished charcoal concrete floors in open-plan luxury home with stone fireplace and floating staircasePolished dark concrete floor in restaurant bar area with branded bar stools, tap handles and TVsMetallic epoxy floor in dark amber and brown marble swirl pattern with mirror-like gloss finishMetallic epoxy floor with colorful light-ray inlays at Brady Theatre in performing arts venueExpansive sealed concrete floor in double-height residential great room with French doors and transom windowsLow-angle dramatic view of polished concrete floor in large warehouse with column reflectionsQuarter-sawn wood-plank concrete overlay detail showing realistic grain texture and warm tonesHigh-gloss sealed outdoor concrete slab with mirror-like reflection of a boat trailer in daytimePolished concrete floor in Westmoore Community Church lobby viewed from wider angle

How far will Bel Covo travel to pour concrete in McCrory?

Bel Covo serves McCrory concrete projects within the standard service radius, and our crews are typically 3-6 weeks booked at any given moment. Every quote is itemized to show the cost of each step of the work, including the mobilization that gets equipment on site, so the quote doubles as the order of operations for your project. On accepted work, billing follows those same steps and shows the completion percentage of each as it happens, with nothing buried in a vague lump sum. Call 870-606-3528 for a straight answer in under two minutes.

Which concrete services does Bel Covo offer in McCrory?

Our McCrory crews handle polished concrete, epoxy and polyaspartic coatings, decorative staining, driveways, patios, and repair work. Every job follows the same Pour-4-Polish process and finish discipline used on our flagship projects. The related links below point to the specific service pages that match common McCrory requests.

What questions come up most about McCrory concrete?

Do you take concrete projects in McCrory, Arkansas?

Yes. McCrory is inside our Eastern Arkansas coverage, about 37 miles northwest of our team. We pour driveways and shop slabs and do garage coatings and polished concrete across Woodruff County. Travel is its own line on every quote, so you see it before you commit.

What does a concrete driveway cost in McCrory?

Driveways in McCrory run $6.96 to $16.43 a square foot, depending on thickness, rebar, and finish. A two-car driveway of about 500 square feet runs $3,650 to $8,650, plus our drive to your site. A drive that small can land above the per-foot range, since setup spreads over fewer feet. The online quote tool gives you your own number in about 2 minutes.

Can you pour and coat a garage floor in the same scope?

Yes. With Pour-4-Polish, we write the pour spec for the coating that goes on it, so the mix, the cure window, and the coating get planned as one job. You get one schedule and one warranty on the workmanship for the whole scope.

Does the Delta clay subgrade in McCrory require special prep?

It does. The river clay under Woodruff County swells when it's wet and shrinks when it dries. So any slab that will get a coating or a polish gets a well-packed base and a moisture vapor barrier first. Skip either one and a Delta floor can lose its finish within two years.

Last updated:

Ready to transform your floor?

Get a free, no-obligation quote for your project.

Woodruff County, Arkansas

See concrete work across Woodruff County, Arkansas →