Skip to main content
Bel Covo
modern sleek onyx polished concrete

Concrete contractor in Ward, AR

What does concrete flooring cost in Ward, Arkansas?

Concrete flooring in Ward runs the same ranges as the broader Arkansas market: polished concrete lands in the low-to-mid single digits per square foot, stained and decorative systems fall in the middle, and high-end epoxy or metallic builds reach the top of the range. Slab condition, square footage, and finish selection all move the real number. The regional breakdown below walks through what actually drives a Ward quote up or down.

Concrete work in Ward

We’re a concrete contractor in Ward, AR. It’s the second-largest city in Lonoke County, and a growing commuter town on the Little Rock metro’s north side. Our concrete work covers driveways for the subdivisions spreading north from Cabot, garage floor coatings for the commuter homes along Interstate 57, and shop slabs out on the rural ring. Our Eastern Arkansas team covers Ward. Get your price in 2 minutes.

Ward sits on the old US-67/167 highway, renamed Interstate 57 in 2024, between Cabot and Beebe. The upgrade brought new homes. Ward is an easy commute to Little Rock and Jacksonville, and that’s who’s moving in. So most jobs here are new subdivision driveways, slab-on-grade home pours, barndominium pads on the rural ring, and garage coatings.

What does a driveway cost in Ward?

Ward driveways run $6.96 to $16.43 a square foot installed. Thickness, reinforcement, and finish move it. A standard two-car driveway of about 500 square feet lands at $3,650 to $8,650 before travel. The low end is a plain slab with fiber and no sealer. Garage coatings and polished floors inside price by the slab’s condition and the system you pick.

Does distance from Eastern Arkansas affect the Ward quote?

Some. Ward sits about 90 miles west of our Eastern Arkansas team, and your quote shows that mobilization up front, so nothing is hidden. On a job of 400 square feet or more, the trip spreads over more feet, so it adds less to each one.

What does the ground in Ward mean for slabs and finishes?

Ward sits on deep loess, a fine silt laid down by wind. It covers the old prairie terraces at the north edge of the Grand Prairie. A couple of feet down there’s a dense, clay-rich layer called a fragipan. It holds water up through the Arkansas winter and early spring. That slows drainage under a slab and raises the moisture risk for any coated or polished floor.

So we pack the base first, and we lay a vapor barrier under any new slab that will get a coating. On an older slab, we look it over before we pick a coating system. If it shows a warning sign, we check it with a moisture meter on site.

There’s an upside, too. The ready-mix here uses rounded river-terrace gravel and quartz-rich sand instead of crushed limestone. So a polished floor inside reads as a warm buff color with amber and honey tones, not the flat gray of a limestone-region pour.

What local aggregate and quarry supply concrete in Ward?

Razorback Concrete Company’s Searcy plant, about 19 miles north in White County, is the ready-mix source for this stretch of I-57. That’s where the river-terrace gravel and quartz sand in a Ward slab come from.

We check every slab in the Grand Prairie zone

Lonoke County's loess fragipan holds seasonal groundwater up near the slab. We look over each existing slab before a coating or polish goes on. If it shows water stains or an old coating that failed, we run a moisture test, so the bond holds through the wet Arkansas spring. New slabs that will be coated get a vapor barrier under them.

What concrete work does our Eastern Arkansas team do in Ward?

Most of the work here is homes and light commercial: driveways for the growing subdivisions, garage coatings for commuter homes, and shop or barndominium pads outside town. Our Eastern Arkansas team handles all three.

Are new driveways the primary work in Ward?

Yes. The new subdivisions keep driveway pours coming on fresh grade. Our standard driveway quote is a 5 inch slab on a packed gravel base, with rebar, poured with a 4500 PSI mix. On any bid you get, look for at least 4,000 PSI. We size control joints to the slab thickness instead of guessing. And since loess drains slowly, a well-packed base keeps the slab from heaving and cracking with the seasons. Driveway details.

What coating system works best for Ward garage floors?

We grind the slab with diamonds first, then coat it. Our standard build is RESA Flake in epoxy: a flake coat under clear epoxy and a urethane topcoat, best indoors. Polyaspartic is the premium build, priced on your quote. It cures fast and shrugs off hot tires, so it’s our garage pick, and it suits shop bays that see fluids or chemicals too. Garage floor coatings.

Shop and barndominium slabs

Detached shops and barndominiums come up often on the rural ring around Ward. A shop slab carries loads a home garage never sees. So it gets rebar, thickened edges under the overhead doors, and a vapor barrier whenever a coating or polish is in the plan. Shop and barn slab details.

Polished concrete for barndominium interiors

Barndominium owners who want a finished floor without tile or carpet often go with polished concrete. The shine comes from grinding the slab itself with finer and finer diamonds. There’s no coat on top to peel or yellow. The local gravel gives it that warm amber and buff tone. Polished concrete details.

Patios and exterior flatwork

Outdoor slabs in Ward sit on the same loess as driveways, so they get the same prep and pour spec. Only the finish changes. Patio and flatwork details.

Get a ballpark on your Ward project online

Answer a few questions about your slab and get a price range before you call anyone. Travel to Ward is already figured in.

Which services does the Pour-4-Polish scope cover?

With Pour-4-Polish, we write one spec for the slab pour, the cure, and the coating or polish, and run them as one job. That’s one spec, one schedule, and one workmanship warranty on the finished surface. If you’re building a new shop or a barndominium pad near Ward, you don’t have to line up two contractors around a cure that takes weeks.

More of our Arkansas coverage

The Arkansas service area page lists the towns along I-57 near Ward and our full coverage.

What the concrete in Arkansas is actually made of

The aggregate story in Arkansas concrete

Arkansas has two kinds of concrete rock, and a polished floor shows which one you got. The northwest Ozarks run on Boone Formation limestone, with 15-30% chert in some Benton County pits. The Delta runs on Mississippi River gravel. The two floors differ so much in color, texture, and how they take a finish that they might as well be in two states.

Northwest cities we cover, like Fayetteville and Fort Smith, are on the Arkansas concrete flooring hub.

What aggregate drives northwest Arkansas polished floors?

Northwest Arkansas runs on Boone Formation limestone (Mississippian age). That stone carries a lot of chert, a hard rock made of silica. Crushed Boone stone goes into structural concrete. Most metro mixes get their sand and gravel from river bars in the White River drainage. Sandstone from the Atoka and Bloyd formations shows up too, but only as a second source in some rural Benton and Carroll County pours.

Polished, these floors read as a light warm gray with a cream-to-bone tint. Off-white and buff-tan chert spots break it up. How many spots you get depends on which pit the ready-mix plant pulled from on pour day. At our standard cut, the floor shows a salt-and-pepper look. Cut deeper, to medium or full aggregate exposure, and it turns into a mottled field with bits of fossil in it. Fossil crinoid stems, the Boone’s best-known mark, show up as small pale disks.

Why does Boone chert leave pinholes in a polished floor?

Porous chert is the headache. The Boone holds lumps of chert, and some are full of tiny holes while some aren’t. Arkansas Geological Survey papers name them as a cause of past quarry problems. In a polished floor, that porous chert grinds faster than the stone around it. That leaves pinholes, dull spots, or pop-outs at the surface, and no amount of densifier fixes them after the fact.

Northwest Arkansas aggregate suppliers include the APAC-Central McClinton-Anchor quarries in Springdale, Hindsville, and Gravette. APAC Valley Springs in Harrison is a second supplier.

Boone stone polishes bright. Acid stains take well on it in earth tones and warm grays. Chert-heavy mixes take stain in patches, because silica doesn’t react with the stain, so a stained floor shows the chert as light freckles on darker stone. Broom finishes look clean and gray. Exposed-aggregate finishes look good here, since you can see both the fossils and the chert.

How does Delta gravel change what a polished floor looks like?

The Delta runs on sand and gravel the Mississippi River laid down, and the coarse rock in it is mostly chert and quartz pebbles. There’s some sandstone, novaculite, and milky vein quartz mixed in, all worn down from older Paleozoic bedrock upstream. There’s next to no local limestone quarry. So crushed stone for the main mixes gets hauled in from Batesville (Independence County) and the Little Rock quarry belt. For jobs in eastern Crittenden County, it comes from Memphis-area plants.

Polished, these floors read warm tan to buff. Cut to the stone, you see creamy cement paste broken up by round chert pebbles from pea-size to marble-size. They come in white, amber, honey, and gray, and now and then you get a rose-red jasper. The whole floor looks warmer and busier than a crushed-limestone floor from northwest Arkansas or southwest Missouri.

What does Delta gravel mean for cracking, stain, and finish?

Round river gravel leaves pebble outlines you can see at a medium or full cut. Some clients love that look. Others call it busy. Some beds of chert-heavy river gravel can also cause alkali-silica reaction, or ASR. That’s when silica in the rock reacts with the cement and swells, which leads to map cracks and pop-outs. Good Delta ready-mix plants guard against it with Class F fly ash. A slab poured with imported rock of unknown origin still carries ASR risk. Still, the expansive clay under Delta slabs is a bigger risk than the rock.

Delta aggregate and ready-mix suppliers include Arkansas Concrete Company, with plants in Forrest City, Wynne, Brinkley, Marianna, and Helena. Others are Razorback Concrete Company (West Memphis, with more than 15 plants), and Forrest City Ready-Mixed Concrete Co.

At a medium cut, a polished Delta-gravel slab has a lot of life. Round pebbles catch light in a way sharp crushed stone doesn’t. Stain goes on in patches. The cement paste takes acid stain fine, but chert pebbles don’t, so the stain makes the contrast stronger. Broom finishes look fairly clean, since the fine sand is rich in quartz. For an even color without the native gravel, the usual Delta choices are epoxy coating over a prepped slab, a self-leveling overlay, or grind-and-seal.

What Does Concrete Work in Ward Look Like?

Polished concrete floor in luxury home entryway reflecting chandelier and modern interior designAction Powersports custom logo embedded in glossy black epoxy showroom floorRound Barn polished concrete floor with mirror-like reflections of windows in dark high-gloss finishPolished charcoal concrete floors in open-plan luxury home with stone fireplace and floating staircasePolished dark concrete floor in restaurant bar area with branded bar stools, tap handles and TVsMetallic epoxy floor in dark amber and brown marble swirl pattern with mirror-like gloss finishMetallic epoxy floor with colorful light-ray inlays at Brady Theatre in performing arts venueExpansive sealed concrete floor in double-height residential great room with French doors and transom windowsLow-angle dramatic view of polished concrete floor in large warehouse with column reflectionsQuarter-sawn wood-plank concrete overlay detail showing realistic grain texture and warm tonesHigh-gloss sealed outdoor concrete slab with mirror-like reflection of a boat trailer in daytimePolished concrete floor in Westmoore Community Church lobby viewed from wider angle

How far will Bel Covo travel to pour concrete in Ward?

Bel Covo serves Ward concrete projects within the standard service radius, and our crews are typically 3-6 weeks booked at any given moment. Every quote is itemized to show the cost of each step of the work, including the mobilization that gets equipment on site, so the quote doubles as the order of operations for your project. On accepted work, billing follows those same steps and shows the completion percentage of each as it happens, with nothing buried in a vague lump sum. Call 870-606-3528 for a straight answer in under two minutes.

Which concrete services does Bel Covo offer in Ward?

Our Ward crews handle polished concrete, epoxy and polyaspartic coatings, decorative staining, driveways, patios, and repair work. Every job follows the same Pour-4-Polish process and finish discipline used on our flagship projects. The related links below point to the specific service pages that match common Ward requests.

What questions come up most about Ward concrete?

Does Bel Covo serve Ward directly?

Yes. Ward is inside the Eastern Arkansas area our team covers. We pour and finish driveways and shop slabs, and we do garage coatings and polished concrete for Lonoke County properties, all under one spec.

What does a concrete driveway cost in Ward?

Ward driveways run $6.96 to $16.43 a square foot installed, depending on thickness, reinforcement, and finish. A two-car driveway, about 500 square feet, lands at $3,650 to $8,650 before travel. The online quote tool gives you a number for your own project.

Can you pour and coat a garage floor in the same scope?

Yes. Our Pour-4-Polish process sets the pour spec for the coating before the truck comes. The pour, the cure time, and the coating run as one job on one schedule, with one workmanship warranty on the finished floor.

Is Ward too small or too far for Bel Covo?

No. Ward and the Lonoke County area around it are part of our regular Eastern Arkansas service area. Rural shops, barndominiums, ranch and farm slabs, and lake-area builds are everyday work for us.

Last updated:

Ready to transform your floor?

Get a free, no-obligation quote for your project.

Lonoke County, Arkansas

See concrete work across Lonoke County, Arkansas →