Skip to main content
Bel Covo
modern sleek onyx polished concrete

Concrete contractor in Ackerman, MS

What does concrete flooring cost in Ackerman, Mississippi?

Concrete flooring in Ackerman runs the same ranges as the broader Mississippi market: polished concrete lands in the low-to-mid single digits per square foot, stained and decorative systems fall in the middle, and high-end epoxy or metallic builds reach the top of the range. Slab condition, square footage, and finish selection all move the real number. The regional breakdown below walks through what actually drives a Ackerman quote up or down.

The Choctaw County seat, where forest-edge builds meet county-government flatwork

Ackerman is the Choctaw County seat, about 76 miles southwest of our North Mississippi team. As a concrete contractor in Ackerman, MS, we pour courthouse-district flatwork in town and shop slabs and barndominium pads out on the rural edge. The ground here is Coastal Plain clay. It holds water and moves with the seasons, so we prep the subgrade before anything else.

Why does the county-seat building stock drive the slab spec?

Most of the work here is exterior flatwork around the courthouse, store slabs along the main roads, and supplier-park pads on rural lots. All of them share one rule. The clay under Choctaw County holds moisture and moves from season to season. So any slab that will get a coating or a polish needs a well-packed base and a vapor barrier to stop ground moisture from coming up through it.

Our standard starts with a 4,000 PSI minimum mix and control joints cut to match the slab’s thickness. We saw-cut those joints within the first day after the pour, before the slab picks its own crack lines. Skip the joints on this clay and cracks show up on top within two to three winters. For steel, we suggest #4 rebar on 18-inch centers. Fiber mesh helps stop small cracks as the slab dries and shrinks, but it doesn’t take the place of steel. Driveway and flatwork details.

How much does a commercial slab cost in Choctaw County?

Commercial slabs run $5.32 to $15.61 a square foot, depending on thickness, steel, and how much ground work the site needs. A 2,000-square-foot supplier-park pad or store slab runs $10,650 to $31,200 before travel and before any coating. The online tool gives you a price for your project in 2 minutes. Get your price.

What kind of stone and aggregate reaches Ackerman?

North Mississippi sits on Coastal Plain ground with no local hard-rock quarry. So concrete in Choctaw County uses regional chert gravel and limestone trucked in from outside. The nearest ready-mix plant we track is MMC Materials - Starkville Plant, next door in Oktibbeha County. Its mixes blend in the regional chert. But chert-rich rock changes color and size more from batch to batch than crushed limestone does. On a polished floor, that gives a warm beige cream surface with scattered tan and rust chert flecks. It’s a warm look that suits shop and barndominium interiors. To keep the color even once the grind shows the rock, we pull every pour for a polished job from the same plant on the same mix ticket.

Chert-rich gravel can react with the cement and crack the slab from inside. That’s called alkali-silica reaction. A good mix fights that with 20 percent or more Class F fly ash and a low-alkali cement. Asking for that mix up front costs nothing, and we ask for it on chert-heavy pours.

How do shop slabs and barn builds differ along the forest edge?

Outside town, the county is rural. Detached shops, working barns, and barndominiums make up a big share of the work. Buildings on bigger parcels near the Tombigbee National Forest line often carry heavy equipment, stored hay, or livestock pens. That’s more load than a home garage ever sees. Our shop and barndominium slab spec thickens the edges at the overhead doors. Heavy-use floors get a 4-inch minimum slab with #4 rebar on 18-inch centers. A floor that will get a coating later gets a vapor barrier, too. Shop slabs with rebar start at $7.04 a square foot for our standard slab. The quote tool prices a thicker one.

With seasonal rain on clay, packing the base matters more here than on sandy ground that drains fast. A slab poured over loose fill in Choctaw County settles unevenly, one part sinking more than another, within five years.

Small-job scheduling note

We send crews to the Ackerman area from our North Mississippi team, about a two-hour drive, so a single small patio or one-car garage floor may not pencil on its own trip. We'll quote it anyway. Small jobs often come together when we can pair them with another Choctaw County project the same week, and we'll tell you straight if that pairing is likely.

Garage floor coatings and polished concrete for Ackerman properties

Coating and polishing work here shows up in county service buildings, home garages in the older Ackerman neighborhoods, and the post-frame shops along county roads outside town.

A garage or shop floor gets diamond grinding to CSP 3, a profile rough enough for the coating to grip. Then comes our standard flake floor (RESA Flake), at $8.55 to $10.39 a square foot. That’s an epoxy build with a flake coat, clear epoxy, and a thin urethane top. When the floor sees fuel or solvents, we talk through the premium polyaspartic build, priced on your quote.

A polished floor on a shop or barndominium interior starts with a rough grind to open up the rock. Then we step through finer grits. A densifier and a guard coat finish it at the shine you pick, for $3.83 to $6.25 a square foot. Our Pour-4-Polish process writes the pour spec for the finish, so a new slab is built for it. The workmanship carries a written warranty on the craft and the install. Material defects fall outside our workmanship warranty and are handled separately.

See what your Ackerman floor costs

Answer a few questions about your project and get a ballpark price, no waiting on a callback.

How does the North Mississippi team cover Choctaw County?

Crews dispatch from our North Mississippi team along US-278 and MS-9. That covers the whole county, out to the lake builds by Choctaw Lake in the Tombigbee National Forest. Check the Mississippi service area for nearby cities.

What the concrete in Mississippi is actually made of

The aggregate story in north Mississippi concrete

North Mississippi concrete, in the Tupelo and Oxford markets, runs on local chert gravel plus limestone hauled in from out of state. No one quarries commercial-grade limestone in the area. The local rock is Coastal Plain chert gravel and sand. It comes from the Tuscaloosa Gravels and from Pleistocene river terraces older than the loess, along the Mississippi-Alabama line from Tishomingo through Lowndes County. The closest limestone quarries sit 1 to 2 hours away, in Alabama or north-central Mississippi.

Our Mississippi concrete flooring hub lists the north Mississippi cities we serve.

Where does north Mississippi aggregate actually come from?

Crushed limestone comes in by truck or rail. Most of it is from north Alabama, out of the Fort Payne Formation at quarries like Vulcan Materials’ Fort Payne Quarry, and some comes from central Tennessee. Distance costs money. That haul shows up in the concrete price, unlike in states with hard rock close by.

The cement comes from outside too, from plants in Alabama, Tennessee, or Missouri. Lowndes County had its own cement plant, Holcim’s Artesia plant, until Holcim mothballed it in 2009 and quit making cement there for good in 2011. Amrize has owned the site since Holcim spun it off in 2025.

Rogers Group’s yard at the Port of Columbus, in Lowndes County, takes in crushed limestone by barge. None of it comes out of the ground there. Foley Materials’ Columbus Quarry sells sand, gravel, and railroad ballast across the Southeast. And APAC Mississippi runs an MDOT-approved gravel pit at Tremont.

How does the imported-aggregate mix affect polished floors?

A polished floor here reads light gray to warm beige cream, with scattered tan and rust flecks of chert. Source matters. A mix heavy on Alabama or Tennessee limestone polishes to a cleaner, more even pale gray. One heavy on Tuscaloosa chert gravel shows more color change and a warmer tone.

The coarse rock travels far and comes from several competing sources, not one quarry face. So mixes here change more from pour to pour than where hard rock is close. If you want a polished concrete finish to match across slabs poured on different days, the spec should name one source pit before the first pour. Chert-heavy gravel polishes with an earth-tone speckle. Deeply weathered chert can cause pop-outs, small chips that break loose from the surface, so polished work should call for dense, washed chert. Tuscaloosa chert can also react with the cement and crack the slab from inside. That’s called alkali-silica reaction (ASR). The answer is ASTM C1260/C1567 testing on the local chert, at least 20 percent Class F fly ash or at least 25 percent slag, and low-alkali cement (Na2Oeq at or under 0.60 percent). Stain comes out mottled and natural-looking instead of even, much like it does on Memphis concrete. Plan for that. Broom finishes are simple, and local crews know them well.

What Does Concrete Work in Ackerman Look Like?

Polished concrete floor in luxury home entryway reflecting chandelier and modern interior designAction Powersports custom logo embedded in glossy black epoxy showroom floorRound Barn polished concrete floor with mirror-like reflections of windows in dark high-gloss finishPolished charcoal concrete floors in open-plan luxury home with stone fireplace and floating staircasePolished dark concrete floor in restaurant bar area with branded bar stools, tap handles and TVsMetallic epoxy floor in dark amber and brown marble swirl pattern with mirror-like gloss finishMetallic epoxy floor with colorful light-ray inlays at Brady Theatre in performing arts venueExpansive sealed concrete floor in double-height residential great room with French doors and transom windowsLow-angle dramatic view of polished concrete floor in large warehouse with column reflectionsQuarter-sawn wood-plank concrete overlay detail showing realistic grain texture and warm tonesHigh-gloss sealed outdoor concrete slab with mirror-like reflection of a boat trailer in daytimePolished concrete floor in Westmoore Community Church lobby viewed from wider angle

How far will Bel Covo travel to pour concrete in Ackerman?

Bel Covo serves Ackerman concrete projects within the standard service radius, and our crews are typically 3-6 weeks booked at any given moment. Every quote is itemized to show the cost of each step of the work, including the mobilization that gets equipment on site, so the quote doubles as the order of operations for your project. On accepted work, billing follows those same steps and shows the completion percentage of each as it happens, with nothing buried in a vague lump sum. Call 662-356-3528 for a straight answer in under two minutes.

Which concrete services does Bel Covo offer in Ackerman?

Our Ackerman crews handle polished concrete, epoxy and polyaspartic coatings, decorative staining, driveways, patios, and repair work. Every job follows the same Pour-4-Polish process and finish discipline used on our flagship projects. The related links below point to the specific service pages that match common Ackerman requests.

What questions come up most about Ackerman concrete?

Do you take concrete projects in Ackerman, Mississippi?

Yes. Ackerman is inside our North Mississippi coverage, about 76 miles southwest of our North Mississippi team. We handle driveways, shop slabs, garage coatings, and polished concrete across Choctaw County. Crews dispatch from our North Mississippi team, and travel shows as its own line on every quote, so you see it before you commit.

What does a concrete driveway cost in Ackerman?

Ackerman driveways run $6.96 to $16.43 a square foot, set by thickness, steel, and finish. Our standard quote is a 5-inch slab with rebar on a packed gravel base. A two-car drive of about 500 square feet runs $3,650 to $8,650 before travel. A small drive runs above the per-foot range, since setup spreads over fewer feet.

Can you pour and coat a garage floor in the same scope?

Yes. Our Pour-4-Polish process handles the pour, the cure, and the coating as one scope of work. One spec covers the pour and the finish, so the slab is built for the coating before the truck arrives. You get one schedule and one warranty on the workmanship.

Is Ackerman too small or too far for Bel Covo?

No. Ackerman and the rest of Choctaw County are part of our regular North Mississippi service area. Rural shops, barndominiums, ranch and farm slabs, and lake-area builds are core work for us, not exceptions.

Last updated:

Ready to transform your floor?

Get a free, no-obligation quote for your project.