Skip to main content
Bel Covo
modern sleek onyx polished concrete

Concrete contractor in Coffeeville, MS

What does concrete flooring cost in Coffeeville, Mississippi?

Concrete flooring in Coffeeville runs the same ranges as the broader Mississippi market: polished concrete lands in the low-to-mid single digits per square foot, stained and decorative systems fall in the middle, and high-end epoxy or metallic builds reach the top of the range. Slab condition, square footage, and finish selection all move the real number. The regional breakdown below walks through what actually drives a Coffeeville quote up or down.

A dual county seat on the Yalobusha arm of Grenada Lake

Coffeeville is one of the two county seats in Yalobusha County, on the Yalobusha arm of Grenada Lake. We’re a concrete contractor in Coffeeville, MS, and the work runs from flatwork around the courthouse square to slabs for lake cabins. Our North Mississippi team works the town from about 80 miles east, and we pour and finish each job under one scope. Get your price now.

Why does the build mix here run from courthouse to lake cabin?

The county courthouse still anchors Main Street. It brings in commercial, government, and institutional flatwork that a lake town alone wouldn’t have.

On the Grenada Lake shore, the jobs are cabin slabs, dock approaches, and garage floors for weekend homes. They sit by the boat ramps at Gums Crossing, Young’s Landing, and North Graysport. On the wooded land west of town, owners build shops and barndominiums, not tract homes.

One scope for the pour and the finish

Pour-4-Polish puts the pour and the coating or polish into one scope of work and one schedule, with a limited workmanship warranty on the finished slab. A small job on its own often pairs with another Yalobusha County job on the same trip, and the quote will say so.

What stone and aggregate does Coffeeville concrete use?

Yalobusha County sits on the Wilcox Group, sand and lignite-streaked clay from the Eocene, under a cap of Coastal Plain chert gravel and Pleistocene terrace soil. That’s not the Tuscaloosa Gravels formation farther east along the Alabama line. On high ground, the chert gravel packs down well. But the Yalobusha River bottoms and the lakeshore edges sit over a high water table, and vapor rising from it can push a coating loose. So on a low cabin or lakeside slab, we run a calcium chloride test (ASTM F1869) before we settle on a coating.

Ready-mix here comes from plants like B & B Concrete Co’s Oxford plant in Lafayette County. Ground and honed, the local rock reads a warm beige with tan and rust chert flecks. A cleaner limestone mix won’t give a polished floor that look. Chert can also react with cement over the years and crack a slab from inside (alkali-silica reaction). So on chert-heavy pours, we check the mix with an ASTM C1260 test before we lock it in. Polished concrete details.

How do driveways and slabs price out in Coffeeville?

A Coffeeville driveway runs $6.96 to $16.43 a square foot installed. For a two-car drive near 500 square feet, figure $3,650 to $8,650, with travel to your site added on top. A drive that small lands above the per-foot range, because setup spreads over fewer feet. Our standard driveway quote is a 5 inch slab of 4,500 PSI concrete on packed gravel, with rebar. Driveway details.

Shop floors and garage coatings around Coffeeville

Coffeeville shop and barn slabs, like other industrial concrete flooring in Mississippi, need heavier steel and thickened edges under the overhead doors, sized to the load. We price them from the slab size and that load. Shop slab details.

For a garage coating, we diamond-grind the slab so the resin can grip. The coating is our RESA Flake floor, with colored chips broadcast into wet resin. The standard build is epoxy, and it runs $8.55 to $10.39 a square foot. The premium build is polyaspartic. It cures fast and shrugs off hot tires, so it’s our garage pick, and it resists chemicals in a working shop. It’s priced on your quote. Garage floor coatings.

See what your Coffeeville floor costs

Enter your square footage and project type for a ballpark estimate.

Which other Yalobusha County cities does Bel Covo cover?

Water Valley, the county’s other seat, and Oakland share Yalobusha County with Coffeeville. Our North Mississippi team covers both, plus Grenada just south. For the full map, see our Mississippi service area page.

What the concrete in Mississippi is actually made of

The aggregate story in north Mississippi concrete

North Mississippi concrete, in the Tupelo and Oxford markets, runs on local chert gravel plus limestone hauled in from out of state. No one quarries commercial-grade limestone in the area. The local rock is Coastal Plain chert gravel and sand. It comes from the Tuscaloosa Gravels and from Pleistocene river terraces older than the loess, along the Mississippi-Alabama line from Tishomingo through Lowndes County. The closest limestone quarries sit 1 to 2 hours away, in Alabama or north-central Mississippi.

Our Mississippi concrete flooring hub lists the north Mississippi cities we serve.

Where does north Mississippi aggregate actually come from?

Crushed limestone comes in by truck or rail. Most of it is from north Alabama, out of the Fort Payne Formation at quarries like Vulcan Materials’ Fort Payne Quarry, and some comes from central Tennessee. Distance costs money. That haul shows up in the concrete price, unlike in states with hard rock close by.

The cement comes from outside too, from plants in Alabama, Tennessee, or Missouri. Lowndes County had its own cement plant, Holcim’s Artesia plant, until Holcim mothballed it in 2009 and quit making cement there for good in 2011. Amrize has owned the site since Holcim spun it off in 2025.

Rogers Group’s yard at the Port of Columbus, in Lowndes County, takes in crushed limestone by barge. None of it comes out of the ground there. Foley Materials’ Columbus Quarry sells sand, gravel, and railroad ballast across the Southeast. And APAC Mississippi runs an MDOT-approved gravel pit at Tremont.

How does the imported-aggregate mix affect polished floors?

A polished floor here reads light gray to warm beige cream, with scattered tan and rust flecks of chert. Source matters. A mix heavy on Alabama or Tennessee limestone polishes to a cleaner, more even pale gray. One heavy on Tuscaloosa chert gravel shows more color change and a warmer tone.

The coarse rock travels far and comes from several competing sources, not one quarry face. So mixes here change more from pour to pour than where hard rock is close. If you want a polished concrete finish to match across slabs poured on different days, the spec should name one source pit before the first pour. Chert-heavy gravel polishes with an earth-tone speckle. Deeply weathered chert can cause pop-outs, small chips that break loose from the surface, so polished work should call for dense, washed chert. Tuscaloosa chert can also react with the cement and crack the slab from inside. That’s called alkali-silica reaction (ASR). The answer is ASTM C1260/C1567 testing on the local chert, at least 20 percent Class F fly ash or at least 25 percent slag, and low-alkali cement (Na2Oeq at or under 0.60 percent). Stain comes out mottled and natural-looking instead of even, much like it does on Memphis concrete. Plan for that. Broom finishes are simple, and local crews know them well.

What Does Concrete Work in Coffeeville Look Like?

Polished concrete floor in luxury home entryway reflecting chandelier and modern interior designAction Powersports custom logo embedded in glossy black epoxy showroom floorRound Barn polished concrete floor with mirror-like reflections of windows in dark high-gloss finishPolished charcoal concrete floors in open-plan luxury home with stone fireplace and floating staircasePolished dark concrete floor in restaurant bar area with branded bar stools, tap handles and TVsMetallic epoxy floor in dark amber and brown marble swirl pattern with mirror-like gloss finishMetallic epoxy floor with colorful light-ray inlays at Brady Theatre in performing arts venueExpansive sealed concrete floor in double-height residential great room with French doors and transom windowsLow-angle dramatic view of polished concrete floor in large warehouse with column reflectionsQuarter-sawn wood-plank concrete overlay detail showing realistic grain texture and warm tonesHigh-gloss sealed outdoor concrete slab with mirror-like reflection of a boat trailer in daytimePolished concrete floor in Westmoore Community Church lobby viewed from wider angle

How far will Bel Covo travel to pour concrete in Coffeeville?

Bel Covo serves Coffeeville concrete projects within the standard service radius, and our crews are typically 3-6 weeks booked at any given moment. Every quote is itemized to show the cost of each step of the work, including the mobilization that gets equipment on site, so the quote doubles as the order of operations for your project. On accepted work, billing follows those same steps and shows the completion percentage of each as it happens, with nothing buried in a vague lump sum. Call 662-356-3528 for a straight answer in under two minutes.

Which concrete services does Bel Covo offer in Coffeeville?

Our Coffeeville crews handle polished concrete, epoxy and polyaspartic coatings, decorative staining, driveways, patios, and repair work. Every job follows the same Pour-4-Polish process and finish discipline used on our flagship projects. The related links below point to the specific service pages that match common Coffeeville requests.

What questions come up most about Coffeeville concrete?

Do you take concrete projects in Coffeeville, Mississippi?

Yes. Coffeeville is inside our North Mississippi coverage, about 80 miles west of our North Mississippi team. We handle home, rural, and civic concrete across Yalobusha County and along MS-7. Crews come out on scheduled trips, and the quote lists travel on a line of its own before you commit.

What does a concrete driveway cost in Coffeeville?

Most Coffeeville driveways run $6.96 to $16.43 a square foot installed, set by thickness, reinforcement, and joint layout. A two-car drive near 500 square feet runs $3,650 to $8,650 plus travel. At that size it can top the per-foot range, since setup spreads over less floor. Put your own size into the online quote tool.

Does the Yalobusha County ground affect how a slab is poured?

Yes. Lots on the lakeshore and the river bottoms near Grenada Lake sit over a higher water table, and that water can rise up under a coating. On a low cabin or lakeside slab, we test for moisture before we pick the coating. On chert-heavy mixes, we check for alkali-silica reaction too.

Can you handle a lake-cabin concrete project near Grenada Lake?

Yes. Cabin slabs, dock approaches, and weekend-home garage floors around Gums Crossing and Graysport are work we're set up for. With Pour-4-Polish, the pour and the finish run as one scope of work, and a limited workmanship warranty on the finished slab covers it. We write the pour spec for the finish.

Last updated:

Ready to transform your floor?

Get a free, no-obligation quote for your project.

Yalobusha County, Mississippi

See concrete work across Yalobusha County, Mississippi →