Skip to main content
Bel Covo
concrete pool deck repair and resurface

Concrete repair and resurfacing in Mississippi

  • Concrete Craftsmen Since 2004
  • North Mississippi Coverage
  • Slabs Built for the Finish
  • On-Site Moisture Testing

Concrete repair and resurfacing in Mississippi

Concrete repair and resurfacing in Mississippi runs $8.27 to $22.41 a square foot across our North Mississippi work, before the drive cost (our trip to your site). Where you land in that range comes down to one question: is the ground under the slab still moving? If it has stopped, we fix the crack or put a new surface on top. If it’s still moving, a patch comes back in 12 to 24 months, so we fix the base first.

Our Memphis team covers DeSoto County, from Olive Branch and Southaven down to Hernando, Horn Lake, and Walls. Our North Mississippi team covers Tupelo along US-78, and Oxford in Lafayette County. We take work in Tunica, too. Every job carries a 1-year workmanship warranty on the install. Our concrete repair and resurfacing page covers how we do the work anywhere we pour. The Mississippi concrete flooring hub covers the rest of the state.

How can you tell a repair job from a resurfacing job?

Repair fixes one failure at its source. That might be a crack, a spall (a spot where the top has popped loose), scaling, or a broken joint. Resurfacing puts a new wear surface on concrete that’s still sound, with no tear-out. Plenty of jobs need both. Say an Olive Branch driveway has de-icer flaking and a few hairline cracks. We’d inject the cracks with structural epoxy (ASTM C881) first, then lay a thin cement overlay across the whole slab.

You can sort most slabs yourself before anyone comes out:

  • The two sides of the crack sit level. It’s most likely a normal shrinkage crack, and it’s fine to repair.
  • One side sits higher than the other. The slab has dropped. No crack filler can stop that.
  • The top flakes or pits, but the slab is solid. That’s resurfacing.
  • Cracks come back after a patch, or step like stairs at the corners. The clay underneath is still moving. That’s a base problem first.

When we resurface a home’s entryway, a flaking front entry or stoop that has stopped moving takes our thin overlay, starting at $4.36 a square foot. The range above includes setup. A single rate can sit a little under it.

Which concrete repair systems do we use in Mississippi?

The system follows the failure. It also depends on whether the slab is sound and whether the ground under it has stopped moving.

  • Structural epoxy injection (ASTM C881). We set small ports along a crack and pump in a thin epoxy that glues the slab back together, which makes it a structural concrete repair, not just a filler. It carries load across the crack again and keeps water out. We use it on garages and inside commercial slabs that are cracked but have stopped moving.
  • Rout and seal. We cut the crack into a clean groove and fill it with a polyurethane or polyurea sealant that bends. It moves with the slab instead of cracking again. It’s our standard fix for clay-driven cracks, and for control and isolation joints, when a full structural repair isn’t in the job.
  • Thin cement overlay (ASTM C928). A polymer-modified cement skin over sound concrete that’s flaking, scaling, or just tired looking. Our standard overlay goes on about as thick as a nickel. We rough up the surface first to CSP 5 or more under ICRI 310.2R. CSP is the roughness number you’ll see on bids, from 1 (smooth) to 10 (rough).
  • Partial-depth repair. For spalls, edge breaks, and broken corners. We take the spot down to solid concrete, coat it with a bonding agent (ASTM C1059), and rebuild the top with polymer repair mortar.
  • Full-depth replacement. We saw out the failed section and swap the clay under it for 4 to 6 inches of packed rock fill. Then we pin the new concrete to the old with steel dowels and pour it with the joints where they belong.
  • What comes after. Ongoing sealed concrete upkeep, polished concrete restoration on commercial floors, and a cove transition where the repair reaches the wall.

How do Mississippi’s clay and climate shape concrete repair?

Yazoo clay is the swelling clay Mississippi is known for. Its main belt runs through central Mississippi, around Yazoo City and Jackson. Up here, the clay under much of DeSoto County acts the same way. It soaks up winter and spring rain and swells. Then a hot summer dries it out, it shrinks, and support pulls out from under the slab.

The slab bridges that gap until the next wet season shoves it back up. The push and pull hits hardest at the edges and corners. That’s where you get diagonal cracks and stair-step cracks. You also get hollow spots under the slab, and they show right through a cosmetic overlay. On higher ground, and on commercial pads built on engineered fill, we find Coastal Plain chert gravel instead.

The fix at pour time is 4 to 6 inches of packed rock fill in place of the clay. On an old slab, we hand-auger the soil before we quote a repair when the cracks point to moving clay. We judge the base the way ACI 546R lays out. That’s the industry’s guide for concrete repair.

Check the ground before you fix the crack. Clay that swells and shrinks is behind most cracked slabs in North Mississippi. Our workmanship warranty is on the install. It can’t hold a slab up while the ground under it keeps moving. On moving clay, the fix that lasts is full-depth replacement with a new base, or piers that reach down past the clay that moves. Another overlay won’t do it.

Mississippi humidity and damp slabs

Humidity here runs 70 to 85 percent most of the year, and higher in summer. Water that comes up through a garage floor or a below-grade slab brings salts with it. The water dries off at the top and leaves a white crust (efflorescence). Then the top starts to flake. That crust means water is moving through the slab. Resurface over it without fixing the water, and the new top fails in 6 to 18 months.

A below-grade slab sits close to wet ground, so it’s a warning sign. We check every slab, and when one looks damp, we run an ASTM F2170 probe test. A probe sits in the slab for 24 hours and reads the humidity inside it. The slab has to read under the system’s limit before an overlay or coating goes down. That’s usually 75 percent for water-based systems and 80 percent for solvent-based ones. The calcium chloride test (ASTM F1869) is a backup, since it reads low on tight modern concrete.

Damp air also slows the cure. A polymer-modified overlay here takes 1 to 3 days longer to cure than it would somewhere drier, so we build that into the schedule. Winter adds wear, too. North Mississippi sees about 40 to 65 freeze-thaw cycles a winter. The de-icer people put down after a hard freeze can flake the top of a driveway.

What concrete repair project types do we run across Mississippi?

Inside work runs all year. Outside work runs March through October, when temperatures stay in the 50 to 90 degree range the materials need.

Driveways and sidewalks in Olive Branch, Southaven, and Hernando

DeSoto County driveways and sidewalks poured between 2000 and 2010 are reaching the 15 to 25 year mark, when clay failures show up. You’ll see diagonal cracks across the slab, stair-step cracks at the expansion joints, and edge flaking from de-icer after a hard winter. A full driveway runs 600 to 1,400 SF. Sidewalk jobs run 100 to 400 LF. If the cracks show a pattern, we hand-auger before we quote. Patching works once the ground has settled and stopped. If the clay is still moving, the section comes out.

How do garage floor repairs handle MS humidity and clay?

A garage here deals with moisture everywhere, and with clay where it’s present. Cracks from shrink-swell, a pitted top from de-icer and damp air, and white crust at the joints are the usual damage. We work it in this order:

  1. We check the slab. If we see white crust or damp spots, we run the F2170 probe test.
  2. If the cracks form a pattern, we hand-auger to check the soil.
  3. We prep the surface under ICRI 310.2R.
  4. We use the repair that fits: a thin overlay for damage on the surface only, or epoxy injection for structural cracks in a sound slab.

Most garage repairs here run 400 to 800 SF.

What about commercial flatwork repair in Tupelo and Oxford retail?

Tupelo and the US-78 corridor bring the commercial work. Think older shopping center lots, store entrances, and restaurant flatwork. Around 15 to 20 years in, they’ve got flaking, failed joints, and pattern cracks bad enough to fix. Oxford has the same kind of work on a smaller scale, downtown and along University Avenue. It adds rental turnovers and fix-ups before a house goes up for sale. A store entrance and apron job runs 2,000 to 8,000 SF. We work in phases around the property manager’s or GC’s schedule, so the lot stays open.

What goes wrong on pool decks and patios?

Chlorine and salt water scale the top of a pool deck. Settling opens hairline cracks, and the joint at the pool coping fails. The UV index runs 9 to 10 from May through August, and that breaks down sealers not rated for sun. So we only use UV-stable systems when we resurface a pool deck. A thin overlay fixes a sound deck, and partial-depth repair handles spot flaking and broken edges. A home pool deck runs 300 to 800 SF, and it takes 24 to 72 hours longer to cure here than in a drier place.

How do industrial slab repairs handle shrink-swell cracking?

We fix warehouse and light factory slabs in Olive Branch, Southaven, and around Tupelo. Forklifts chew up the joints. Shrink-swell drops one side of the slab lower than the other. We inject epoxy where a section is cracked but sound, and refill worn control joints with polyurea. Forklift dings get partial-depth repair. When clay forces a full-depth job, we phase the tear-out and pour around your production schedule. Most of these jobs run 1,500 to 6,000 SF.

How much does concrete repair cost in Mississippi?

Most repair and resurfacing jobs here land at $8.27 to $22.41 a square foot. That range includes setup. A single rate can sit a little under it. Crack work prices by the linear foot instead.

Repair typeTypical rangeCommon project size
Crack chasing and joint sealing$2.55 per LF50 to 300 LF
Thin cement overlay (resurfacing)From $4.36 per SF400 to 1,400 SF
Partial-depth repair$7.89 per SFSpalls, edges, and corners
Epoxy injection (structural cracks)$15.40 per LF30 to 150 LF
Full-depth slab replacementFrom $18.36 per SF400 to 1,400 SF

What moves your price is the ground first. Clay that’s still moving means full-depth replacement and a new base. After that comes the kind of damage and the size of the job. Surface prep and how hard the spot is to reach count, too. The concrete repair and resurfacing cost guide breaks it down by repair type. Every quote shows the drive cost as its own line.

Get your Mississippi concrete repair project priced online

Enter your square footage and the kind of damage. Tell us if the slab sits on clay or on fill. You get an itemized price with your repair options laid out.

Which Mississippi cities do we serve for concrete repair?

  • Olive Branch, Southaven, Hernando, and Horn Lake in DeSoto County, where our Memphis team works the subdivision driveways and garages south of Memphis
  • Tupelo and the stores and commercial lots along US-78
  • Oxford and the rest of Lafayette County

Outside those areas, send us the address and we’ll look at it.

Price your Mississippi concrete repair project

Each part shows on its own line: the check, the repair, the prep, and the drive. It takes about two minutes to get a real number.

See the results

Resurfaced residential pool deck with smooth concrete and brick-pattern coping surrounding curved poolCommercial retail sidewalk repaired and resurfaced with gray overlay and circular rock planter insetsCurved residential sidewalk with repaired center and decorative brick-pattern overlay border edgingSmooth concrete overlay on historic home exterior porch slabLuxury residential pool with repaired and resurfaced concrete deck, spa, and water featurePolished concrete surface showing multi-panel color remediation with scored pattern lines in gray, tan, and green tonesBathroom shower substrate repair showing veined marble-look concrete overlay panels and glass enclosure

Frequently asked questions

What does concrete repair and resurfacing cost in North Mississippi?

Most repair and resurfacing work across North Mississippi runs $8.27 to $22.41 a square foot. Routing and sealing a crack runs $2.55 a linear foot. Structural epoxy injection runs $15.40 a linear foot. A thin overlay on a sound, flaking slab starts at $4.36 a square foot. The range includes setup. A single rate can sit a little under it. Full-depth replacement starts at $18.36 a square foot, with tear-out and a new base. The drive cost shows as its own line on every quote.

Why does Yazoo clay cause so many slab failures in North Mississippi?

Yazoo clay is the swelling clay Mississippi is known for. Its main belt runs through central Mississippi, around Yazoo City and Jackson. Up here, the clay under much of DeSoto County acts the same way. It swells when winter rain soaks it and shrinks in the summer heat, and that pulls support out from under the slab. Edges and corners crack first. The fix at pour is 4 to 6 inches of packed rock fill in place of the clay.

What is the difference between concrete repair and concrete resurfacing in Mississippi?

Repair fixes one failure at its source: a crack, a spall, scaling, or a broken joint. Resurfacing lays a new wear surface over sound concrete, with no tear-out. Plenty of jobs need both. A flaking Olive Branch driveway with a few hairline cracks might get epoxy in the cracks, then a thin overlay across the top. Resurfacing only holds on a slab that has stopped moving. The install carries a 1-year workmanship warranty on our work.

How does Mississippi humidity affect concrete repair and resurfacing?

Humidity here runs 70 to 85 percent most of the year. It pushes water and salts up through garage floors and below-grade slabs. That leaves a white crust (efflorescence) and a flaking top. Resurface over it without fixing the water, and the new surface fails in 6 to 18 months. When a slab looks damp, we run an ASTM F2170 probe test before install. The damp air also slows an overlay's cure by 1 to 3 days, and we plan for it.

Last updated:

Ready to transform your floor?

Get a free, no-obligation quote from our team.