Skip to main content
Bel Covo
modern sleek onyx polished concrete

Concrete contractor in Houston, MS

What does concrete flooring cost in Houston, Mississippi?

Concrete flooring in Houston runs the same ranges as the broader Mississippi market: polished concrete lands in the low-to-mid single digits per square foot, stained and decorative systems fall in the middle, and high-end epoxy or metallic builds reach the top of the range. Slab condition, square footage, and finish selection all move the real number. The regional breakdown below walks through what actually drives a Houston quote up or down.

Courthouse blocks and farm shops in Houston

Houston is one of Chickasaw County’s two county seats, a courthouse block ringed by row crops and cattle land. As a concrete contractor in Houston, MS, we pour storefront flatwork in town and shops, barns, and driveways on the farms. Our North Mississippi team drives about 34 miles southwest to get here. The clay under the chert gravel holds water after rain, so we pack the base hard first. Get your price now.

What kind of concrete work does Houston need?

It splits two ways. Near the courthouse, it’s commercial and civic flatwork. Out on the farmland and rural lots, it’s working floors and outbuildings: shop floors, equipment-barn pads, long driveways, and the inside finish in a barndominium. Before we quote the order of work, we look at what the slab is for, how much moisture it’s likely to see, what it has to carry, and when the finish needs to go on.

New concrete pours

Driveways and approaches. Under Chickasaw County lots, chert gravel sits on top of clay-heavy Pleistocene terrace soil. That clay soaks up rain and stays wet, so packing the base matters more here than in sandy ground. We compact all the way down and cut control joints spaced for the slab’s thickness. Our standard driveway quote is a 5 inch slab with rebar, set on packed gravel and poured from a 4,500 PSI mix. You’ll see bids at 4,000 PSI with fiber mesh. Treat 4,000 PSI as the floor for any bid, not the goal. Driveway details.

Shop and barn slabs. Working buildings come up a lot around Houston, because equipment storage, cattle pens, and farm-equipment repair all put more weight on a floor than a home garage does. We add rebar, thicken the edges under overhead doors, and lay a moisture vapor barrier under any slab that will get a coating or polish later. Shop slab details.

Patios and flatwork. A patio in Houston sits on the same soil as a driveway. The prep matches, and only the finish menu changes. Patio details.

Concrete finishing

Garage floor coatings. We diamond-grind a Houston garage floor to open up the surface, then lay the coating system. Home garages usually get a chip-broadcast finish, while a shop that sees chemicals gets a polyaspartic topcoat instead. Garage floor coatings.

Polished concrete. A barndominium or shop interior that needs a finished look without tile or carpet is a good fit for polish. The shine is ground into the slab itself, so there’s no topcoat to peel. Polished concrete details.

Pour-4-Polish: the pour spec starts at the finish

Pouring a new slab in Houston that you plan to coat or polish? With Pour-4-Polish, we write the pour spec for the floor that goes on it, so the slab is ready for its finish on day one. You get one scope, one point of contact from start to sign-off, and a workmanship warranty on the finished install.

What stone and aggregate does Chickasaw County concrete use?

North Mississippi has no local hard-rock quarry, so ready-mix here leans on Coastal Plain chert gravel, not the crushed limestone you see in pours around the bigger mid-South cities. B & B Concrete Co - Okolona Plant supplies Chickasaw County from Okolona, the other county seat. Chert gravel is round, not sharp-edged like crushed stone. Polished, it reads as a warm beige cream with tan and rust flecks, and it takes densifier and stain well.

That chert brings two things to plan for:

  1. Color from pour to pour. The mix can vary more between loads than it does where the rock is quarried. If you want a polished floor to match across several pours, spec one gravel pit for all of them.
  2. Slow cracking from inside. Local chert can react with the cement over the years and crack long-lived flatwork. That’s called alkali-silica reaction (ASR). On outdoor slabs, we hold the water-to-cement ratio at 0.45 or lower and confirm the mix guards against ASR before we lock it in.

How much do concrete floors and driveways cost in Houston?

Three things set the price: the square footage, the shape an old slab is in when we coat or polish it, and the system you pick. Polished concrete runs $3.83 to $6.25 a square foot. A flake garage floor in our standard epoxy build runs $8.55 to $10.39. Polyaspartic is the premium build, priced on your quote.

Driveways run $6.96 to $16.43 a square foot. A two-car driveway of about 500 square feet runs $3,650 to $8,650. That bottom number is a plain fiber slab with no sealer. On a drive this size, the top number can land over the per-foot range, because setup is spread across fewer feet. Our trip to your site is its own line on the quote.

See what your Houston floor costs online

Answer a few questions about your project and get a price right away, with no waiting on a callback.

Which other Chickasaw County cities does Bel Covo serve?

The 34 mile trip from our North Mississippi team shows on your quote before you commit. That same team also works Okolona, Vardaman, Calhoun City, West Point, and Tupelo.

What the concrete in Mississippi is actually made of

The aggregate story in north Mississippi concrete

North Mississippi concrete, in the Tupelo and Oxford markets, runs on local chert gravel plus limestone hauled in from out of state. No one quarries commercial-grade limestone in the area. The local rock is Coastal Plain chert gravel and sand. It comes from the Tuscaloosa Gravels and from Pleistocene river terraces older than the loess, along the Mississippi-Alabama line from Tishomingo through Lowndes County. The closest limestone quarries sit 1 to 2 hours away, in Alabama or north-central Mississippi.

Our Mississippi concrete flooring hub lists the north Mississippi cities we serve.

Where does north Mississippi aggregate actually come from?

Crushed limestone comes in by truck or rail. Most of it is from north Alabama, out of the Fort Payne Formation at quarries like Vulcan Materials’ Fort Payne Quarry, and some comes from central Tennessee. Distance costs money. That haul shows up in the concrete price, unlike in states with hard rock close by.

The cement comes from outside too, from plants in Alabama, Tennessee, or Missouri. Lowndes County had its own cement plant, Holcim’s Artesia plant, until Holcim mothballed it in 2009 and quit making cement there for good in 2011. Amrize has owned the site since Holcim spun it off in 2025.

Rogers Group’s yard at the Port of Columbus, in Lowndes County, takes in crushed limestone by barge. None of it comes out of the ground there. Foley Materials’ Columbus Quarry sells sand, gravel, and railroad ballast across the Southeast. And APAC Mississippi runs an MDOT-approved gravel pit at Tremont.

How does the imported-aggregate mix affect polished floors?

A polished floor here reads light gray to warm beige cream, with scattered tan and rust flecks of chert. Source matters. A mix heavy on Alabama or Tennessee limestone polishes to a cleaner, more even pale gray. One heavy on Tuscaloosa chert gravel shows more color change and a warmer tone.

The coarse rock travels far and comes from several competing sources, not one quarry face. So mixes here change more from pour to pour than where hard rock is close. If you want a polished concrete finish to match across slabs poured on different days, the spec should name one source pit before the first pour. Chert-heavy gravel polishes with an earth-tone speckle. Deeply weathered chert can cause pop-outs, small chips that break loose from the surface, so polished work should call for dense, washed chert. Tuscaloosa chert can also react with the cement and crack the slab from inside. That’s called alkali-silica reaction (ASR). The answer is ASTM C1260/C1567 testing on the local chert, at least 20 percent Class F fly ash or at least 25 percent slag, and low-alkali cement (Na2Oeq at or under 0.60 percent). Stain comes out mottled and natural-looking instead of even, much like it does on Memphis concrete. Plan for that. Broom finishes are simple, and local crews know them well.

What Does Concrete Work in Houston Look Like?

Polished concrete floor in luxury home entryway reflecting chandelier and modern interior designAction Powersports custom logo embedded in glossy black epoxy showroom floorRound Barn polished concrete floor with mirror-like reflections of windows in dark high-gloss finishPolished charcoal concrete floors in open-plan luxury home with stone fireplace and floating staircasePolished dark concrete floor in restaurant bar area with branded bar stools, tap handles and TVsMetallic epoxy floor in dark amber and brown marble swirl pattern with mirror-like gloss finishMetallic epoxy floor with colorful light-ray inlays at Brady Theatre in performing arts venueExpansive sealed concrete floor in double-height residential great room with French doors and transom windowsLow-angle dramatic view of polished concrete floor in large warehouse with column reflectionsQuarter-sawn wood-plank concrete overlay detail showing realistic grain texture and warm tonesHigh-gloss sealed outdoor concrete slab with mirror-like reflection of a boat trailer in daytimePolished concrete floor in Westmoore Community Church lobby viewed from wider angle

How far will Bel Covo travel to pour concrete in Houston?

Bel Covo serves Houston concrete projects within the standard service radius, and our crews are typically 3-6 weeks booked at any given moment. Every quote is itemized to show the cost of each step of the work, including the mobilization that gets equipment on site, so the quote doubles as the order of operations for your project. On accepted work, billing follows those same steps and shows the completion percentage of each as it happens, with nothing buried in a vague lump sum. Call 662-356-3528 for a straight answer in under two minutes.

Which concrete services does Bel Covo offer in Houston?

Our Houston crews handle polished concrete, epoxy and polyaspartic coatings, decorative staining, driveways, patios, and repair work. Every job follows the same Pour-4-Polish process and finish discipline used on our flagship projects. The related links below point to the specific service pages that match common Houston requests.

What questions come up most about Houston concrete?

Does Bel Covo serve Houston directly?

Yes. Houston is inside our North Mississippi service area. We pour driveways and shop slabs, and we do garage coatings and polished concrete for Chickasaw County homes, farms, and businesses.

What does a concrete driveway cost in Houston?

Houston driveways run $6.96 to $16.43 per square foot installed. Thickness, rebar, and finish set where yours lands. Our standard drive is a 5 inch slab with rebar on packed gravel, poured from a 4,500 PSI mix. Put your own size into the quote tool for a real number.

Why does Chickasaw County have two county seats, and does that affect where you work?

Floods used to cut the eastern part of the county off from Houston, so Okolona became a second seat. It doesn't limit us. We work both ends of the county, from commercial flatwork near the Houston courthouse to shop and barn slabs out toward Okolona.

Is Houston too small or too far for Bel Covo?

No. Houston and the Chickasaw County countryside are part of our regular North Mississippi service area. Rural shops, barndominiums, ranch and farm slabs, and lake-area builds are core work for us, not side jobs.

Last updated:

Ready to transform your floor?

Get a free, no-obligation quote for your project.

Chickasaw County, Mississippi

See concrete work across Chickasaw County, Mississippi →