Skip to main content
Bel Covo
modern sleek onyx polished concrete

Concrete contractor in Myrtle, MS

What does concrete flooring cost in Myrtle, Mississippi?

Concrete flooring in Myrtle runs the same ranges as the broader Mississippi market: polished concrete lands in the low-to-mid single digits per square foot, stained and decorative systems fall in the middle, and high-end epoxy or metallic builds reach the top of the range. Slab condition, square footage, and finish selection all move the real number. The regional breakdown below walks through what actually drives a Myrtle quote up or down.

A furniture-town floor problem: industrial loads on small-town slabs

We’re a concrete contractor in Myrtle, MS, and the concrete work runs heavier than a town of 502 people suggests. A furniture plant on Highway 178 puts forklift traffic and coating systems on slabs that most residential crews never spec. Warehouse pours need denser reinforcement, and coatings need chemical-resistant topcoats. One crew pours and finishes, so there is no handoff.

What makes Union County concrete work different from surrounding counties?

Union County sits on the Interstate 22 freight corridor, which means the work mix tilts toward industrial and commercial slabs at a rate unusual for a county its size. The furniture cluster runs presses, hoists, and loaded forklifts across plant floors daily. A coating on a floor like that must bond at CSP 3 minimum, cure with a chemical-resistant polyaspartic, and go down on a substrate that passes a moisture evaluation if the slab is old enough to carry prior coating generations. A standard residential garage spec does not transfer to that environment. We price and spec Union County industrial work as its own category, not as a scaled-up residential job.

Plant-floor re-coating: what to expect

If you are re-coating an existing upholstery-plant or warehouse slab in Union County, budget for diamond grinding to CSP 3 and a moisture evaluation before the topcoat goes down. Older slabs in this corridor carry decades of forklift traffic and coating chemistry; skipping the prep is the most common reason a coating fails inside two years.

What local aggregate goes into a Myrtle concrete pour?

The gravel feeding pours in this part of north Mississippi is Coastal Plain chert gravel, not the limestone common further south. APAC-Mississippi’s New Albany operation, in Union County, is the close crushed-stone source for most projects in the Myrtle orbit. B&B Concrete’s New Albany plant supplies ready-mix for residential and smaller commercial pours. Chert-gravel aggregate grinds to a warm beige-tan surface flecked with rust tones when polished, which suits the barndominium interiors and shop finishes we do in the rural ring around Myrtle. One technical note: chert-rich aggregate can carry reactive silica, so any polished concrete spec in this county gets an ASR-aware cementitious blend to prevent late-stage map cracking. The polished concrete price range runs $3.83 to $6.25 per square foot depending on aggregate exposure and sheen level.

How does Bel Covo schedule concrete work in Myrtle?

Our North Mississippi team covers Myrtle, about 36 miles northwest of North Mississippi. Crews dispatch from our North Mississippi team along MS-178 and Interstate 22, booking as scheduled mobilizations rather than same-week dispatch. Our crews are typically 3-6 weeks booked. Every quote lists mobilization as a separate line item so you see the travel cost before committing.

New concrete in Union County

Residential driveways in Myrtle spec to a 4,000 PSI minimum pour over compacted subgrade, with fiber mesh reinforcement and control joints placed for the slab thickness. The Coastal Plain sandy loam over chert-gravel terrace soils is firm when compacted properly, but the soft pockets in lower-lying areas need careful subgrade verification before a plant-scale pour. Driveway pricing runs $6.96 to $16.43 per square foot installed. Driveway details.

Shop and barn slabs for the rural ring around Myrtle carry heavier loads than a home garage sees: thickened edges at overhead-door openings, a vapor barrier under any slab that will eventually be coated, and reinforcement sized to the actual stored and rolling weight. Shop slab details.

Patio and approach flatwork sits in the same soil zone as driveways and shares the prep spec. The finish choices open up at the surface: broom finish, exposed aggregate, or a stamped pattern. Patio details.

Concrete coatings and polished floors

Garage floor coatings in Myrtle start with diamond grinding to CSP 3, then the chip-broadcast system for residential work or a chemical-resistant polyaspartic when the floor carries tool storage and automotive chemicals. Garage floor coatings.

Polished concrete works well for the shop and barndominium interiors where a cleanable surface matters but tile is off the table. The finish is ground into the slab itself, not a topcoat layer over it. Polished concrete details.

The Pour-4-Polish process covers both in one scope: we pour the slab, hold the cure window, and apply the coating or polish without a second contractor handoff. Our workmanship warranty for the project covers both the pour and the finish as a single scope.

See what your Myrtle floor costs online

Enter your project details and get a ballpark price, no callback required.

Which other Union County and North Mississippi cities does Bel Covo serve?

The Mississippi service area page carries the full 2026 coverage map for Union County and neighboring counties on the I-22 corridor.

What the concrete in Mississippi is actually made of

The aggregate story in north Mississippi concrete

North Mississippi concrete, in the Tupelo and Oxford markets, runs on local chert gravel plus limestone hauled in from out of state. No one quarries commercial-grade limestone in the area. The local rock is Coastal Plain chert gravel and sand. It comes from the Tuscaloosa Gravels and from Pleistocene river terraces older than the loess, along the Mississippi-Alabama line from Tishomingo through Lowndes County. The closest limestone quarries sit 1 to 2 hours away, in Alabama or north-central Mississippi.

Our Mississippi concrete flooring hub lists the north Mississippi cities we serve.

Where does north Mississippi aggregate actually come from?

Crushed limestone comes in by truck or rail. Most of it is from north Alabama, out of the Fort Payne Formation at quarries like Vulcan Materials’ Fort Payne Quarry, and some comes from central Tennessee. Distance costs money. That haul shows up in the concrete price, unlike in states with hard rock close by.

The cement comes from outside too, from plants in Alabama, Tennessee, or Missouri. Lowndes County had its own cement plant, Holcim’s Artesia plant, until Holcim mothballed it in 2009 and quit making cement there for good in 2011. Amrize has owned the site since Holcim spun it off in 2025.

Rogers Group’s yard at the Port of Columbus, in Lowndes County, takes in crushed limestone by barge. None of it comes out of the ground there. Foley Materials’ Columbus Quarry sells sand, gravel, and railroad ballast across the Southeast. And APAC Mississippi runs an MDOT-approved gravel pit at Tremont.

How does the imported-aggregate mix affect polished floors?

A polished floor here reads light gray to warm beige cream, with scattered tan and rust flecks of chert. Source matters. A mix heavy on Alabama or Tennessee limestone polishes to a cleaner, more even pale gray. One heavy on Tuscaloosa chert gravel shows more color change and a warmer tone.

The coarse rock travels far and comes from several competing sources, not one quarry face. So mixes here change more from pour to pour than where hard rock is close. If you want a polished concrete finish to match across slabs poured on different days, the spec should name one source pit before the first pour. Chert-heavy gravel polishes with an earth-tone speckle. Deeply weathered chert can cause pop-outs, small chips that break loose from the surface, so polished work should call for dense, washed chert. Tuscaloosa chert can also react with the cement and crack the slab from inside. That’s called alkali-silica reaction (ASR). The answer is ASTM C1260/C1567 testing on the local chert, at least 20 percent Class F fly ash or at least 25 percent slag, and low-alkali cement (Na2Oeq at or under 0.60 percent). Stain comes out mottled and natural-looking instead of even, much like it does on Memphis concrete. Plan for that. Broom finishes are simple, and local crews know them well.

What Does Concrete Work in Myrtle Look Like?

Polished concrete floor in luxury home entryway reflecting chandelier and modern interior designAction Powersports custom logo embedded in glossy black epoxy showroom floorRound Barn polished concrete floor with mirror-like reflections of windows in dark high-gloss finishPolished charcoal concrete floors in open-plan luxury home with stone fireplace and floating staircasePolished dark concrete floor in restaurant bar area with branded bar stools, tap handles and TVsMetallic epoxy floor in dark amber and brown marble swirl pattern with mirror-like gloss finishMetallic epoxy floor with colorful light-ray inlays at Brady Theatre in performing arts venueExpansive sealed concrete floor in double-height residential great room with French doors and transom windowsLow-angle dramatic view of polished concrete floor in large warehouse with column reflectionsQuarter-sawn wood-plank concrete overlay detail showing realistic grain texture and warm tonesHigh-gloss sealed outdoor concrete slab with mirror-like reflection of a boat trailer in daytimePolished concrete floor in Westmoore Community Church lobby viewed from wider angle

How far will Bel Covo travel to pour concrete in Myrtle?

Bel Covo serves Myrtle concrete projects within the standard service radius, and our crews are typically 3-6 weeks booked at any given moment. Every quote is itemized to show the cost of each step of the work, including the mobilization that gets equipment on site, so the quote doubles as the order of operations for your project. On accepted work, billing follows those same steps and shows the completion percentage of each as it happens, with nothing buried in a vague lump sum. Call 662-356-3528 for a straight answer in under two minutes.

Which concrete services does Bel Covo offer in Myrtle?

Our Myrtle crews handle polished concrete, epoxy and polyaspartic coatings, decorative staining, driveways, patios, and repair work. Every job follows the same Pour-4-Polish process and finish discipline used on our flagship projects. The related links below point to the specific service pages that match common Myrtle requests.

What questions come up most about Myrtle concrete?

Do you take concrete projects in Myrtle, Mississippi?

Yes. Myrtle is inside our North Mississippi coverage, about 36 miles northwest of North Mississippi. We handle commercial, residential, and industrial concrete across Union County and along the Interstate 22 corridor. Crews dispatch from our North Mississippi team and book as scheduled mobilizations. Travel costs are itemized on every quote so the mobilization line is visible before you commit.

What does a concrete driveway cost in Myrtle?

Myrtle driveways generally run $6.96 to $16.43 per square foot installed, depending on thickness, reinforcement, and finish. A two-car residential driveway of about 500 square feet typically lands at $3,650 to $8,650. The online quote tool returns a ballpark for your specific project.

Can you re-coat an existing plant or warehouse floor in Union County?

Yes. We spec plant-floor re-coats differently from residential garage work: diamond grinding to CSP 3, a moisture evaluation on older slabs, and a chemical-resistant polyaspartic or urethane topcoat rated for forklift and chemical exposure. A workmanship warranty limited to the applied system covers the coating phase.

Does chert aggregate affect polished concrete in this part of Mississippi?

It does. Chert-rich aggregate can carry reactive silica, so polished concrete pours in Union County get an ASR-aware cementitious blend to prevent late-stage map cracking. The chert also grinds to a warm beige-tan surface with rust flecks, which gives polished slabs here a distinct appearance compared to limestone-aggregate floors further south.

Last updated:

Ready to transform your floor?

Get a free, no-obligation quote for your project.