Skip to main content
Bel Covo
modern sleek onyx polished concrete

Concrete contractor in Somerville, TN

What does concrete flooring cost in Somerville, Tennessee?

Concrete flooring in Somerville runs the same ranges as the broader Tennessee market: polished concrete lands in the low-to-mid single digits per square foot, stained and decorative systems fall in the middle, and high-end epoxy or metallic builds reach the top of the range. Slab condition, square footage, and finish selection all move the real number. The regional breakdown below walks through what actually drives a Somerville quote up or down.

Concrete for Fayette County

Somerville is the Fayette County seat, and the downtown square, the homes, and the farms around town all sit on deep loess silt that shifts as it gets wet and dries out. So as a concrete contractor in Somerville, TN, we pack the subgrade before every pour. Our Memphis team does driveways, shop slabs, garage coatings, and polished concrete here. Garage floor coatings in Somerville run $8.55 to $10.39 a square foot. Get your price now.

Why does Fayette County’s soil need extra prep on every slab?

Fayette County soil starts with deep loess, a fine silt the wind laid down, over older Mississippi River deposits. That loess packs down when its moisture changes, and West Tennessee’s wet winters change it a lot. So a few things aren’t optional here: a pour of at least 4,000 PSI and a packed subgrade under it. Before any coating, we check the slab, and we test its moisture when the check turns up a warning sign. Weather sets some start dates, too. A coating waits for the slab to dry out after a long wet spell, because a slab coated while it’s still holding that water traps vapor that later blisters the floor. Build it that way and a Somerville driveway can last 30 years. Pour it on soft silt and it can crack inside five.

Concrete services Bel Covo brings to Somerville

Every Fayette County quote starts from four questions: what the slab is for, how wet it gets, what rolls on it, and when it’s due.

New concrete

Driveways and approaches. Somerville driveways run $6.96 to $16.43 a square foot. That’s our standard driveway quote. It’s 5 inches thick over a packed gravel base, reinforced with #4 rebar every 18 inches, poured at 4500 PSI, and cured under a sprayed-on membrane. We cut control joints to match the slab thickness. On this loess, packing the base is the step that matters most. Comparing bids? Each one should carry at least 4 inches and 4,000 PSI with 4 to 6 percent air. Driveway details

Shop and barn slabs. Fayette County’s farms bring us detached shops and working barns. We reinforce those slabs and thicken the edges at overhead door openings, and any slab that will be coated or polished later gets a vapor barrier under it. Shop slab details

Patios and flatwork. A Somerville patio sits on the same soil as the driveway, so it gets the same base prep. Our patios start with fiber mesh in place of rebar. The finish is where your choices open up: broom, salt, smooth trowel, or exposed aggregate. Patio details

Which finish fits a Somerville garage or shop?

Garage floor coatings. We diamond grind the slab first to open it up for the resin. Our standard garage floor in Somerville is epoxy flooring, the RESA Flake build: a flake coat 18 to 22 mils thick (a mil is a thousandth of an inch), a clear epoxy layer of 16 to 18 mils, and a thin 4 mil urethane top. If the garage doubles as a shop, or you need it back fast, look at the premium polyaspartic build, our garage pick. It cures fast and shrugs off hot tires, and we price it on your quote. Garage floor coatings

Polished concrete. Polished floors suit Somerville shop and barndominium interiors that should look finished where tile or carpet won’t work. We grind the shine into the concrete itself. Our standard polish is a 30 grit cut that shows a salt-and-pepper look. Polished concrete details

One spec from slab to seal

Pouring a fresh slab you also want polished or coated? Our Pour-4-Polish process writes the pour spec for the finish that goes on it and treats the pour and the finish as one scope: one mobilization, one schedule, and one workmanship warranty on the full job.

What stone and aggregate does Somerville ready-mix carry?

Fayette County ready-mix draws on Memphis Stone & Gravel’s sand and gravel mines in Shelby County. They pull Mississippi River gravel full of chert, a hard stone that comes in a lot of colors, so concrete here sets up a warm cream-to-buff color flecked with multicolor pebble. Cement and ready-mix also come through Buzzi Unicem USA Ready-Mix - Millington (3239 Fite Rd., Millington, TN), an active plant serving West Tennessee.

That chert gravel polishes well. Grind down to the rock and you get a warm, speckled floor with the pebbles showing through. Want a more even gray? A self-leveling overlay serves you better than a full grind and polish. Chert can also react with cement and crack a slab from inside, which is called alkali-silica reaction (ASR). So on polished pours, the standard here is a mix with Class F fly ash and a low-alkali cement.

Is Somerville’s growth changing the project mix here?

Yes. Somerville is a town of 3,094 people, and Fayette County keeps picking up spillover from suburban Memphis. In the county seat, that means commuter homes, small commercial flatwork on the square, and working farm buildings.

How do Somerville concrete costs break down by job?

New pours run $5.32 to $15.61 a square foot. Coating a ground garage slab costs $8.55 to $10.39 a square foot, depending on the build and how thick the flake goes. A polished floor costs $3.83 to $6.25 a square foot. How much rock shows and how high the shine goes set where you land. Mobilization from our Memphis team is in every quote, and our quote tool does the math in two minutes.

Nearby cities are on the Tennessee service area page.

See what your Somerville floor costs online

Answer a few questions about your project and get a ballpark price. Mobilization is already in the number.

What the concrete in Tennessee is actually made of

The aggregate story in West Tennessee concrete

Memphis and West Tennessee concrete uses Mississippi River chert gravel and sand from local pits. Crushed limestone comes in by rail or barge from Middle Tennessee (the Fort Payne Formation and the Mississippian limestone above it). West Tennessee has no hard-rock limestone quarry. Its bedrock sits under hundreds of feet of loose Coastal Plain sediment, so any coarse limestone in a Memphis slab has come 150 miles or more. Our Tennessee concrete flooring page covers where we work.

What gives Memphis polished floors their multi-toned cream look?

The river gravel is old Devonian and Mississippian chert, worn round over hundreds of miles of river. So the pebbles run gray, brown, red, cream, and black. No crushed-limestone area has that range. A polished floor reads as a warm cream to buff, peppered with tan, honey, gray, and reddish-brown pebbles. Ground and honed, it looks speckled, not one clean color. Darker gravel mixes lean toward a light khaki. A mix made with shipped-in limestone polishes closer to an even pale gray, the quieter choice.

Weathered chert can be porous, and it can react with cement and crack a slab from inside (alkali-silica reaction). Good producers screen for it. The loess bluffs (wind-blown silt) east of the river add silty sand to local mixes. That can raise how much water a hot-weather pour needs.

Local producers and cement

Memphis Stone and Gravel, part of Granite Construction, is the biggest local producer. It runs 3 sand and gravel mines in Mississippi River deposits and is building a fourth. Cement comes down the river by barge from Cape Girardeau and Festus, Missouri, to the Buzzi Unicem USA terminal at the Port of Memphis. No cement kiln runs in West Tennessee.

Does the river aggregate create problems for stain or coating finishes?

For stain, yes. Chert pebbles take acid stain poorly while the cement around them takes it well, so stained floors here come out mottled. A broom finish hides the gravel, though round gravel makes a tight cream harder to bring up. Polish shows the chert loud and clear. That’s character in a home or a small shop. On a big commercial floor meant to look even gray, it’s busy.

So pick by the look you want:

  • Speckled and many-toned: polish a river-gravel slab.
  • Even pale gray: ask for a limestone mix before the pour. An old slab keeps the look it has.
  • One even color on an existing slab: an epoxy coating over the ground slab covers the gravel.

What about Nashville, Knoxville, and Chattanooga?

Middle and East Tennessee have crushed stone quarries close to town: Rogers Group’s Whites Creek quarry in Nashville, Vulcan Materials’ Dixie Lee quarry in Farragut near Knoxville, and Martin Marietta and Vulcan quarries in Chattanooga. Our Nashville, Knoxville, and Chattanooga teams work that side of the state. A mix made with that crushed limestone polishes closer to an even pale gray than the river-gravel floors above.

What Does Concrete Work in Somerville Look Like?

Ground-level close-up of completed white vinyl chip epoxy floor showing chip texture and depth with service counter visible in distanceCompleted white vinyl chip epoxy floor in Ladd's showroom with worker in background and Club Car branding bannersCompleted white vinyl chip epoxy floor at Ladd's showroom looking toward service counter and green accent wallReflective brown polished concrete floor with fully exposed stone aggregate.Glossy brown polished concrete floor with exposed aggregate beside built in cabinets.full exposure polished concrete floor in a residential great room by Bel CovoPolished concrete floor in luxury home entryway reflecting chandelier and modern interior designAction Powersports custom logo embedded in glossy black epoxy showroom floorRound Barn polished concrete floor with mirror-like reflections of windows in dark high-gloss finishPolished charcoal concrete floors in open-plan luxury home with stone fireplace and floating staircasePolished dark concrete floor in restaurant bar area with branded bar stools, tap handles and TVsMetallic epoxy floor in dark amber and brown marble swirl pattern with mirror-like gloss finish

How far will Bel Covo travel to pour concrete in Somerville?

Bel Covo serves Somerville concrete projects within the standard service radius, and our crews are typically 3-6 weeks booked at any given moment. Every quote is itemized to show the cost of each step of the work, including the mobilization that gets equipment on site, so the quote doubles as the order of operations for your project. On accepted work, billing follows those same steps and shows the completion percentage of each as it happens, with nothing buried in a vague lump sum. Call 901-589-3528 for a straight answer in under two minutes.

Which concrete services does Bel Covo offer in Somerville?

Our Somerville crews handle polished concrete, epoxy and polyaspartic coatings, decorative staining, driveways, patios, and repair work. Every job follows the same Pour-4-Polish process and finish discipline used on our flagship projects. The related links below point to the specific service pages that match common Somerville requests.

What questions come up most about Somerville concrete?

Does Bel Covo serve Somerville directly?

Yes. Somerville is inside the West Tennessee coverage of our Memphis team. That team handles driveways, shop slabs, garage coatings, and polished concrete for Fayette County properties. Jobs book as scheduled mobilizations, and travel is itemized on the quote before you commit.

What does a concrete driveway cost in Somerville?

Somerville driveways run $6.96 to $16.43 a square foot, depending on thickness, reinforcement, and finish. A two-car drive of about 500 square feet runs $3,650 to $8,650, plus our drive to your site. Small drives cost more a foot, since setup spreads over fewer feet. The online quote tool gives you a ballpark in two minutes.

Can you pour and coat a garage floor in the same scope?

Yes. Our Pour-4-Polish process handles the pour, the cure, and the coating as one scope of work. We write the pour spec for the coating that goes on it. One spec, one schedule, one workmanship warranty on the full scope.

How does soil type in Fayette County affect slab prep?

Fayette County sits on deep loess silt over Mississippi River deposits. That top layer packs down as its moisture changes, so we compact the subgrade before any pour. Before a coating, we check the slab. We test its moisture when it's old, sits low, or shows water stains. Skip those steps and slabs here crack or peel early.

Last updated:

Ready to transform your floor?

Get a free, no-obligation quote for your project.

Fayette County, Tennessee

See concrete work across Fayette County, Tennessee →