What kind of concrete work is common in Clay County?

The county's economy splits the work three ways. Working ranches across 654,000-plus farmed acres drive ag-shop and equipment pads, usually 6 to 8 inches with #4 rebar sized off the equipment. The century-old oil and gas base puts tank pads and service slabs into the mix at 6 inches or thicker. Henrietta and the smaller towns carry standard 4-inch residential drives and patios plus polished commercial floors on a compacted base.

How does Clay County soil affect a slab?

Clay County sits on Rolling Red Prairies soils: reddish-brown loams over clayey, gypsiferous Permian red-bed subsoils on the Red River. That clay swells wet and shrinks dry, so the durable build compacts the subgrade to about 95 percent Proctor density and lays 4 to 6 inches of crushed base. Because the Permian section carries gypsum, local sand is washed and sulfate-tested before it goes in a slab. On an older slab, a parcel near the Red River or Lake Arrowhead, or a floor with a prior coating failure, on-site moisture testing is added before a coating goes down, because vapor drive through a damp slab is what lifts coatings.

What floor does a Henrietta storefront or county building usually get?

A polished slab is the common choice. Commercial and civic floors in Henrietta take a 4,000 PSI mix ground to a Mohs 7 to 8 wear surface and held to ACI 302.1R flatness tolerances for traffic. Coarse aggregate here is rounded Red River terrace gravel of quartzite, quartz, and chert, and ASTM C1012 and C40 testing keeps sulfate expansion out of the mix.

Concrete in Clay County, TX

Q: Which Clay County towns does Bel Covo serve?

Bel Covo covers Clay County with dedicated pages for Henrietta, the county seat at roughly 3,014 residents, and Petrolia on the county's northwest edge. Henrietta sits where US 287 and US 82 cross and anchors the commercial and civic work; Petrolia carries the oilfield heritage near the Red River. The town rail on this page links both covered Clay County towns.

Concrete across Clay County

Concrete Clay County property owners usually need one of a few things. A driveway or slab, a shop or barn floor, a garage coating, or a polished interior, and Bel Covo pours and finishes every one with a single crew across the 2 Clay County towns it covers. The slab and the finish stay on one schedule.

Clay County is the ranch-and-oilfield county on the Red River, anchored by Henrietta (roughly 3,014 residents) where US 287 from Fort Worth meets US 82. Roughly 10,000 residents spread across 892-plus farms and ranches working 654,000 acres, with cattle, wheat, cotton, and a century-old oil and gas base layered on top. That spread drives a work load weighted toward ag-shop and equipment pads, oilfield service slabs, and small-town residential and civic flatwork across North Texas.

Which Clay County towns does Bel Covo serve?

Henrietta is the county seat and the commercial anchor on US 287 and 82, with most of the residential and civic work tracking the highway corridor; Petrolia carries the oilfield heritage on the county’s northwest edge near the Red River. The town rail below links each covered Clay County town.

Henrietta, the county seat where US 287 and US 82 cross, anchoring the commercial and civic work
Petrolia, the namesake of the first North Texas oilfield, on the county’s Red River edge

Every covered Clay County town has a link in the rail below, and the open country between them falls under the same North Texas reach.

Why does a county-wide crew change a Clay County job?

Clay County stretches from Henrietta on US 287 out to the Red River oilfield country around Petrolia, and one Bel Covo crew pours and finishes across that whole spread rather than handing a slab between trades. That means an ag-shop pad on a working ranch and a downtown Henrietta civic slab both get the same crew that has placed concrete on this Permian red-bed soil for two decades. Scheduling across the covered towns runs off one calendar under our North Texas coverage, so an owner with work in two communities is not juggling separate contractors per address.

What does concrete work look like across Clay County?

The county’s ranching, oilfield, and small-town base sorts the concrete work into a few clear types.

Ag shop slabs and equipment pads. Working ranches across the county’s 654,000 farmed acres run combines, grain carts, and cattle equipment onto shop floors, so these pour at 6 to 8 inches with #4 rebar sized off the equipment list rather than a generic residential spec.
Oilfield service slabs. Clay County has produced oil since the 1904 Hapgood discovery and still pumps natural gas, so tank pads and equipment slabs stay in the mix, typically 6 inches or thicker with a rebar mat sized to the point loads.
Residential drives and patios. Henrietta and the smaller communities carry the standard 4-inch slab on a compacted base, with exterior pours air-entrained at 4 to 7 percent against the roughly 45 to 55 freeze-thaw cycles a North Texas winter brings.
Polished commercial and civic floors. Henrietta storefronts and county buildings take a 4,000 PSI slab polished to a Mohs 7 to 8 wear surface, following ACI 302.1R flatness tolerances for traffic.
Garage and shop coatings. The residential and light-commercial market takes epoxy and polyaspartic systems at 4 to 20 mils over a properly ground slab.

How does the Red River terrace gravels and Permian red-bed prairie soil under Clay County behave?

Clay County sits in the Rolling Red Prairies on the Red River, where upland soils are deep reddish-brown loams over clayey subsoils developed in calcareous and gypsiferous Permian red-bed sediments. That clay subsoil shrinks dry and swells wet, so the slab lives or dies on the prep below it: compact the subgrade to roughly 95 percent standard Proctor density and place 4 to 6 inches of crushed base for drainage and load spread. The coarse aggregate in this market runs well-rounded Quaternary Red River terrace gravel (quartzite, quartz, and chert clasts), and the Permian section carries gypsum beds, so any local sand must be washed and tested before it goes in a slab; ASTM C1012 sulfate-resistance and ASTM C40 organic-impurity testing keep sulfate expansion out of the mix. Crews air-entrain every exterior pour at 4 to 7 percent for the roughly 45 to 55 freeze-thaw cycles the region averages each winter.

The concrete durability guide walks through how the mix and prep hold up over decades.

See what your Clay County concrete costs

Give us the square footage, how the slab gets used, and the site conditions anywhere in Clay County; the quote tool prices it in about two minutes.

Price your project