Skip to main content
Bel Covo
concrete pool deck repair and resurface

Concrete leveling in Texas

  • Concrete Craftsmen Since 2004
  • Texarkana, North Texas & Wichita Falls Coverage
  • Slabs Built for the Finish
  • On-Site Moisture Testing

Concrete leveling in Texas

Concrete leveling in Texas runs $4.72 to $9.38 a square foot. That’s lifting a sunk driveway, walk, patio, or slab back to grade with foam or a cement slurry. No tear-out and no new pour. Clay is usually why it sank. Permian red bed clay can move a slab edge 2 to 6 inches in one year where the ground was never stabilized. Our concrete leveling comes with a 1-year warranty on the workmanship.

Three of our teams work in Texas. Our Texarkana team handles Texarkana and Paris. Our Wichita Falls team handles Wichita Falls. Sherman, Denison, and Bonham get our Southern Oklahoma team.

Which concrete leveling systems does Bel Covo install in Texas?

The right one depends on the soil, how far the slab has to come up, and what sits on it.

  • Polyurethane foam injection. We drill 5/8-inch holes in a grid and pump in a two-part foam. It grows to about 20 times its liquid size and lifts the slab while you watch. It carries load in about 15 minutes. And it adds almost no weight to soil that’s already giving way. So it’s our usual pick for driveways, walks, pool decks, and garage floors in North Texas. You can use the slab the same day.
  • Mudjacking (cement slurry). This is the cement leveling most people have heard of. We pump a heavier cement-and-sand slurry through bigger 1-5/8-inch holes. The material costs less. But it adds 50 to 100 pounds per cubic foot to soil that already let the slab down. We keep it for outdoor slabs where the ground can carry that weight, or where foam gear can’t get in.
  • Subgrade stabilization injection. A foam made to firm up loose or swelling clay under the slab, not to lift it. We add it when a swell test shows the clay is still moving.
  • Void filling. A lighter foam that fills empty pockets without raising the slab. It goes around pipes, along foundation walls, or under loading-bay floors. It closes the path water takes to start the next failure.
  • Work that pairs with a lift. Concrete flatwork repair where the lift shows cracked or flaking spots. Sealing the joints a lift opens. And sealed concrete upkeep to protect the surface through freeze and thaw.

The concrete leveling service page has more on pricing and how the systems compare.

Which lift fits your slab?

  • Sunk, but still in one piece, on steady soil: foam.
  • Outdoor slab on firm soil, and price matters most: mudjacking.
  • Clay still swelling and shrinking: foam plus stabilization.
  • Cracked or flaking on top: a lift fixes height, not the surface, so pair it with a repair.
  • Broken into loose pieces: leveling won’t save it. It needs replacing.

What happens before we quote a lift?

Every leveling job starts with a survey of the slab, before we drill.

  1. Shoot the heights. We measure across the slab to see how far it dropped and which way it tips.
  2. Find the voids. We tap for a hollow sound, look through a small core with a borescope, or use ground-penetrating radar. An empty pocket under the slab lifts clean. Soil that’s still moving drops the slab again in 12 to 24 months unless we firm it up.
  3. Test the clay when the check points to it. An ASTM D4546 swell test rates the clay low, medium, or high for how much it grows when wet. An ASTM D6913 test sorts the soil by grain size. High-swell Permian red bed clay needs foam plus stabilization, not a lift alone.
  4. Screen for sulfate where gypsum is likely. Some pockets of the Permian red beds hold gypsum. If the screen finds sulfate, new concrete poured next to the lift gets Type V sulfate-resistant cement (ASTM C150).
  5. Lay out the holes and walk you through it. You see what the lift fixes and what it leaves for later. Then you pick the scope.

How does Texas’s climate and substrate shape concrete leveling?

Three things decide whether a lift holds for 10 years or sinks back to the same spot inside two.

Permian red bed clay, Annona Chalk, and gypsum sulfate. Permian red bed clay is the top reason slabs sink in North Texas. In active swell zones it has a plasticity index above 35. That means it soaks up a lot of water and changes size a lot. It swells with summer rain and shrinks in the dry late summer. Annona Chalk along the Red River near Paris, Bonham, and Texarkana works another way. It’s strong when dry and weak when soaked, so slabs downhill from a gutter drop at the edge. Gypsum in some Permian pockets puts sulfate against the slab. The sulfate grows crystals (ettringite) in plain cement paste, and they crack the slab from below.

Heat, sun, and freeze. Texas temperatures swing from 30 to 100°F across the seasons. That moves the joints and breaks the seals. Summer UV index runs 11 and up, the highest of our six states. On flatwork in full sun, it wears out a sealer with no UV blocker in 3 to 5 years. North Texas and Texarkana also see 20 to 55 freeze-thaw cycles a winter. Each one works on any joint water has gotten into. Foam rides through freeze and thaw fine, because its closed cells don’t soak up water.

Where do Texas slabs sink the most?

Sherman, Denison, and Paris have a lot of slab-on-grade homes built from the 1980s through the 2000s. Most sit on clay that was never stabilized, and most of those slabs sink 10 to 20 years after the pour. Texarkana has the same kind of homes, plus warehouses along I-30. Wichita Falls adds oilfield shop floors to its homes.

A lift over moving clay won’t last. If the clay under your slab still swells and shrinks and nobody firms it up, the slab drops again. When a swell test rates the clay medium or high, we give you two honest choices. Foam plus stabilization injection, or wait on the lift until the structural fix is planned. You see what we found before you pick.

What concrete leveling project types does Bel Covo run across Texas?

Our concrete leveling projects in Texas come in 5 types: home driveways and walks, garage floors, store lots, pool decks, and industrial floors.

Residential driveway and sidewalk leveling

A sunk cement driveway is the job we level most. Driveways, sidewalks, front walks, and porch slabs in Sherman, Denison, Paris, Bonham, Texarkana, and Wichita Falls show dropped edges, trip hazards, and split joints. Foam is the usual pick, since you can drive on it the same day. A home driveway runs 200 to 800 square feet. A sidewalk or front walk runs 80 to 300.

How do garage floor leveling jobs handle TX expansive clay?

On North Texas expansive clay, a sinking garage floor drops at the door, slopes back toward the wall, and cracks open at the joints. We pump foam through 5/8-inch holes in a grid. That lifts the floor without pulling up the finish on it. A two-car garage runs 400 to 700 square feet, and a three-car up to 1,200. A lift over 2 inches adds stabilization to the job.

What about commercial flatwork and parking-lot leveling?

Strip centers, grocery store pads, and fast-food aprons in North Texas drop at the expansion joints 5 to 10 years after the pour. It’s the same clay that sinks home slabs. We lift them overnight or in slow hours, so the site stays open. A store apron runs 2,000 to 15,000 square feet, and a full parking lot up to 50,000. Then we reseal the joints, so water can’t get back under before the next freeze.

Pool deck and patio lifting

Pool decks on custom homes around Sherman and Texarkana sit on backfill that packs down over the first 3 to 5 years. You’ll see the edge drop at the coping, the deck tip toward the pool, and water sit in low spots. Foam lifts the deck without tearing it out. Its closed cells don’t soak up the pool chemicals that splash on the deck. A home pool deck runs 400 to 1,500 square feet. We can lift a patio next to it on the same visit.

How do industrial and oilfield-adjacent slab leveling jobs handle settlement?

Around Wichita Falls and Texarkana, we level forklift warehouse floors, loading-bay aprons, and oilfield equipment pads. Forklifts, heavy gear, and gypsum in the soil can sink a slab far enough to close an aisle or a loading bay. A dense foam carries the load without the weight mudjacking would add to failing soil. A sulfate screen tells us whether new concrete next to the lift needs Type V cement. Then we seal the joints before the equipment goes back in.

How much does concrete leveling cost in Texas?

Leveling runs $4.72 to $9.38 a square foot. The lift method sets most of it.

SystemTypical range per SFCommon project size
Polyurethane foam (residential exterior)From $9.26200 to 800 SF driveway or walk
Mudjacking (cement-slurry grout)From $4.60200 to 1,500 SF outdoor flatwork
Garage floor and interior slab levelingQuoted per job400 to 1,200 SF
Commercial flatwork and parking-lot levelingQuoted per job2,000 to 50,000 SF
Industrial and oilfield-adjacent slab levelingQuoted per job1,000 to 20,000 SF

The range above includes setup. A single rate can sit a little under it.

These are our 2026 prices for North Texas, Texarkana, and Wichita Falls. We price indoor, store, and plant jobs once we see the access, the size, the load, and how long the floor can be down. Sealing the joints after a lift is its own line, at $2.55 a linear foot. What moves your price most: a lift over 2 inches, stabilization (priced after we see the clay), the swell rating, tight access, and downtime limits at a business. Your quote lists the drive cost on its own line.

Get your Texas concrete leveling priced online

Enter the slab size and pick foam or cement slurry. The quote tool adds joint sealing if you want it and returns an itemized price.

Texas cities we serve for concrete leveling

  • Texarkana and the Red River country across Bowie County, from our Texarkana team
  • Sherman and Grayson County, from our Southern Oklahoma team
  • Denison and the homes around Lake Texoma, from our Southern Oklahoma team
  • Paris and Lamar County along the Red River, from our Texarkana team
  • Wichita Falls and its oilfield work, from our Wichita Falls team

Outside these areas, send us the job and we’ll look at it.

Price your Texas concrete leveling project

Lift method, joint sealing, and the drive cost, itemized in one quote. About two minutes from slab size to a real number.

See the results

Resurfaced residential pool deck with smooth concrete and brick-pattern coping surrounding curved poolCommercial retail sidewalk repaired and resurfaced with gray overlay and circular rock planter insetsCurved residential sidewalk with repaired center and decorative brick-pattern overlay border edgingSmooth concrete overlay on historic home exterior porch slabLuxury residential pool with repaired and resurfaced concrete deck, spa, and water featurePolished concrete surface showing multi-panel color remediation with scored pattern lines in gray, tan, and green tonesBathroom shower substrate repair showing veined marble-look concrete overlay panels and glass enclosure

Frequently asked questions

What does concrete leveling cost in Texas?

Concrete leveling in Texas runs $4.72 to $9.38 a square foot. That range includes setup, so a single rate can sit a little under it. Foam on a home driveway or walk in Sherman, Denison, or Paris starts at $9.26 a square foot for a lift under 2 inches. Mudjacking with a cement slurry starts at $4.60 a square foot. It costs less, but it puts more weight on soil that already let the slab down. A garage floor or indoor slab is priced per job. Access, dust control, and working around the finished floor take more labor. Commercial lots and industrial floors around Wichita Falls and Texarkana are priced per job too, since size, load, and downtime set the cost. Every price covers finding the voids and a 1-year warranty on the workmanship of the lift. The biggest swing on a North Texas job is moving clay. If a swell test shows the clay still swells and shrinks, we add stabilization under the slab, and that adds to the price. Your quote lists the drive cost, our trip to your site, on its own line.

How does Texas climate and substrate cause concrete settlement?

Texas has the hardest shrink-swell cycle of the six states we work in. Permian red bed clay across North Texas swells with summer rain and shrinks in the dry late summer. In active swell zones it has a plasticity index above 35, so it holds a lot of water and changes size a lot. That's how driveways and patios end up with dropped edges, backward slope, and split joints. Annona Chalk along the Red River acts differently. It's strong when dry but loses strength when soaked, so slabs downhill from a gutter drop at the edge. In some Permian pockets, gypsum in the soil puts sulfate against the slab. Sulfate grows crystals (ettringite) in plain cement paste, and they crack the slab from below. New concrete there gets Type V sulfate-resistant cement (ASTM C150). Heat adds to it. Temperatures swing from 30 to 100°F across the seasons. UV index runs 11 and up in summer. And North Texas sees 20 to 55 freeze-thaw cycles a winter.

Can you level existing slabs across Texas residential and commercial sites?

Yes, most of them, across North Texas, Texarkana, and Wichita Falls. We check the slab before we quote a lift. A void under the slab lifts clean. Soil that's still moving drops the slab again unless we firm it up too. Age tells us where to look. Many Texas slabs poured before 2010 sit on native clay with no built-up base under them. A lift fixes how they look, but a real structural fix goes deeper. Slabs poured after 2015 more often sit on a built-up base. On those, we look harder at whether water or a void is causing the movement. We walk you through what we found, so you see what the lift fixes and what it leaves for later. A slab that has broken into loose pieces needs replacing, not leveling.

Which Texas industries and project types use concrete leveling most?

Four kinds of work make up most of it. Homes come first: driveways, walks, garage floors, and patios in Sherman, Denison, Paris, Bonham, and Texarkana, on clay that was never stabilized. Next are strip centers and grocery store aprons. They drop at the expansion joints 5 to 10 years after the pour. Then come pool decks and patios on custom homes around Sherman and the Texarkana acreage. A pool deck sits on backfill that packs down over its first 3 to 5 years, and foam lifts it without tearing it out. Last are warehouse and oilfield floors around Wichita Falls and along the Texarkana freight routes. Forklifts, heavy gear, and gypsum in the soil can sink a slab far enough to close an aisle or a loading bay. Each kind gets its own check, lift method, and price. Out on rural acreage in Lamar, Fannin, Grayson, and Bowie counties, we also level barn, shop, and outbuilding slabs.

Last updated:

Ready to transform your floor?

Get a free, no-obligation quote from our team.