- Concrete Craftsmen Since 2004
- Texarkana, North Texas & Wichita Falls Coverage
- Slabs Built for the Finish
- On-Site Moisture Testing
Concrete repair and resurfacing in Texas
Concrete repair and resurfacing in Texas runs $8.27 to $22.41 a square foot with us, installed. Where your job lands depends on one question. Is the damage only on the surface, or is the ground under the slab causing it? We do concrete repair and resurfacing across North Texas, Texarkana, and Wichita Falls, with a 1-year warranty on our workmanship.
Three kinds of ground cause most of the failures we fix. Wichita Falls sits on Permian red bed clay. The Red River country around Texarkana, Paris, and Bonham sits on Annona Chalk. And pockets of gypsum in the soil quietly eat regular cement. Our Texarkana, Wichita Falls, and Southern Oklahoma teams cover the northern band of the state, from Wichita Falls east through Sherman and Denison to Texarkana. We don’t work Houston, Austin, or San Antonio. The Texas concrete flooring hub covers the rest of the state picture.
Is the problem on the surface or under the slab?
That answer picks the repair, so it’s the first thing we look at. Each sign below points to a different fix.
- The top is flaking or worn, but the slab under it is solid. That’s surface damage. A polymer overlay or a partial-depth patch fixes it.
- A corner broke off, or there’s a deep hole. We saw out the bad concrete and build it back, partway down or all the way through.
- A crack has stopped moving. We pump structural epoxy into it, and the slab carries weight as one piece again.
- One side of a crack sits higher than the other. The slab has dropped. No crack filler can stop that. The section gets cut out and rebuilt. If a panel sank in one piece, we can sometimes lift it instead: we drill small holes and pump foam or a cement slurry under it (mudjacking).
- The top keeps flaking, rock shows through, and there’s a chalky white crust at the cracks. In North Texas, that’s the sign of gypsum sulfate. We check the ground before any new concrete goes in.
Which concrete repair systems do we use in Texas?
Before any bonded repair, we grind the area to a CSP 3 to 5 profile (ICRI 310.2R). CSP is how rough we leave the surface, so the new material can grip.
- Polymer-modified overlay. A thin cement topping, 1/8 to 1/2 inch thick, bonded to a sound slab. It’s for light flaking, worn tops, and a fresh look.
- Partial-depth repair with rapid-set mortar. A patch 1 to 4 inches deep for spalls (chunks broken off the top) and local damage. The mortar meets ASTM C928 and takes traffic again in 4 to 8 hours, so it’s our usual pick on commercial flatwork where downtime costs money.
- Full-depth section repair. We cut the failed part out all the way through, rebuild the base, and pour new concrete flush with the old.
- Structural epoxy injection. For a crack that has stopped moving, we set small ports along it and pump epoxy in under pressure. It’s how we fix cracks that run through a whole industrial slab under forklift loads. We follow the ACI 546R repair guide when we pick the material.
- Type V cement repair pour. Any new pour over known gypsum ground gets Type V sulfate-resisting cement (ASTM C150). Regular portland cement breaks down there. Type V holds up.
- Rout and seal on cracks and joints. We cut the crack or joint into a clean groove, add backer rod in joints, and fill it with polyurethane or silicone sealant that bends with the slab. On commercial flatwork, joints need this every 5 to 7 years.
Repairs often pair with sealed concrete upkeep or refinished concrete flatwork walkways. Our concrete repair and resurfacing cost guide breaks pricing down by system.
How does Texas’s climate and ground (clay, chalk, gypsum) shape concrete repair?
The wrong fix on the wrong failure comes back in 12 to 24 months. In Texas, three things work on a repair at once: the ground, the heat, and the sun.
Red bed clay, Annona Chalk, and gypsum sulfate
Wichita Falls sits on Permian red bed clay. It swells when it’s wet and shrinks when it dries, and the slab on top moves with it. The Red River country through Texarkana, Paris, and Bonham sits on Annona Chalk, a soft limestone from the Cretaceous age. It breaks down under weight and holds water right where the slab meets the ground. That speeds up flaking, and it loosens any repair laid down without something to separate it from that wet layer.
Gypsum is the slow one. Pockets of it run through Grayson, Fannin, Lamar, and Red River counties. The sulfate in it reacts with regular portland cement. Over 5 to 15 years, the top flakes, the rock shows through, and the slab cracks. You’ll see the pattern once you know it: flaking that keeps spreading, bare rock, and a chalky white crust (efflorescence) at the crack edges. Any new pour over suspect ground gets Type V cement. Regular cement fails fast there.
Heat swings, freeze-thaw, and sun
Texas spring and fall run anywhere from 30 to 100 degrees, and North Texas sees 20 to 55 freeze-thaw cycles a winter. That’s harder on the seam between a repair and the old slab than freezing alone, because the push and pull goes on all year. So we pick a repair mortar that grows and shrinks with heat at about the same rate as your slab. That keeps the patch from letting go.
The sun does its own damage. The UV index hits 11 from May through September, and a sealer that isn’t built for sun breaks down in 1 to 3 years. Outdoors, we finish with a UV-stable polyaspartic or aliphatic polyurethane topcoat.
Ask every bidder about sulfate. In Grayson, Fannin, Lamar, and Red River counties, ask how they’ll check the ground for gypsum, and what cement they’ll pour if they find it. The right answer is Type V. Skip the sulfate check and pour regular cement, and the same failure comes back.
What concrete repair project types do we run across Texas?
The jobs run from a 50 SF sidewalk to a 20,000-plus SF warehouse floor, and each kind starts with a different question.
Driveways and sidewalks around Sherman, Denison, and Paris
This is our most common repair. Sherman, Denison, Paris, and Bonham have lots of homes from the 1990s and 2000s, and those slabs now show flaking, failed joints, and broken corners. A driveway usually runs 200 to 800 SF and a sidewalk 50 to 300 SF. The hard part is almost always the diagnosis. Is it surface wear, a crack from the ground moving, or sulfate? When a slab looks suspect, we take a core sample and test the ground for sulfate before we quote.
How do garage floor repairs handle Texas heat cycling?
Garage floors take the heat swings, plus oil and chemical stains, and tops that were never finished well at the first pour. The fix is usually a polymer overlay or a partial-depth patch, topped with a UV-stable topcoat that stands up to chemicals. A two-car garage runs 400 to 800 SF, and a three-car up to 1,200 SF. We match the mortar to how your slab grows and shrinks with heat so it doesn’t let go. Garages in Texarkana and Wichita Falls get the same specs.
What about commercial flatwork in North Texas and Texarkana?
Commercial work means ADA sidewalk fixes, parking lot joints, sunken entry slabs, and storefront refreshes in North Texas retail strips and on Texarkana properties. We use ASTM C928 rapid-set mortar here, because a closed lot costs the owner money. The patch takes traffic again in 4 to 8 hours. Jobs run from a 200 SF entry slab to a 5,000 SF parking lot. We set the schedule with the property manager, so the work happens after hours or when traffic is low.
Pool decks and patios
Around Sherman and Denison, pool decks and patios wear out from sun on old sealers, chlorine flaking the top, and owners who want a new look. The usual fix is a polymer overlay on a sound slab with a UV-stable polyaspartic or aliphatic polyurethane topcoat. A pool deck runs 400 to 1,500 SF, and a patio 200 to 800 SF. In full sun, a sealer that isn’t built for UV breaks down in 1 to 3 years.
How do industrial slab repairs handle structural cracks and sulfate?
Industrial floors cost the most to fix. At oilfield-related sites in Wichita Falls and warehouses in Texarkana, forklifts, worn joints, and cracks from moving soil or sulfate push the work toward full-depth repair. A crack through the whole slab that has stopped moving gets structural epoxy injection, with the surface prepped to ICRI 310.2R. Where gypsum is a concern on Texarkana and Red River jobs, we test for sulfate first. Over the ACI 332 limits, the pour switches to Type V cement. Jobs run from a 500 SF spot repair to a 20,000-plus SF warehouse.
How much does concrete repair and resurfacing cost in Texas?
| System | Typical range per SF | Common project size |
|---|---|---|
| Polymer-modified overlay | From $4.36 | 400 to 1,500 SF |
| Partial-depth repair (ASTM C928) | From $8.19 | 200 to 1,000 SF |
| Full-depth section repair | From $18.36 | 500 to 5,000 SF |
| Rout and seal (cracks and joints) | $2.55 per LF | 200 to 2,000 LF |
Our full repair range includes setup. A single rate can sit a little under it. Structural epoxy injection is priced by the foot of crack, at $15.40 a linear foot.
Your own number is the base repair plus the lines your slab needs. These move it most:
- How deep the damage goes.
- A sulfate check and Type V cement, if the ground calls for it.
- Grinding to a CSP 3 to 5 profile.
- Matching the mortar to the old slab.
- The sealer.
- How hard it is to get our equipment to the slab.
Outdoor overlays book heaviest from March through October, when sealers can cure between 50 and 90 degrees. Indoor and structural repairs run all year. The drive cost (our trip out to your site) is its own line on every quote, figured from our nearest Texas team.
Price your Texas concrete repair online
Enter the square feet, the kind of damage, and how the slab gets used. Flaking, cracks, or structural all count. The quote tool walks you through system, sealer, and prep. Then you get an itemized price.
Texas cities we serve for concrete repair
We repair concrete across the northern band of Texas:
- Texarkana, from our Texarkana team, for retail and warehouse slabs along the Red River
- Sherman and the rest of Grayson County, from our Southern Oklahoma team
- Denison and the Lake Texoma towns, from our Southern Oklahoma team
- Anna, Melissa, and Prosper in Collin County, from our Southern Oklahoma team
- Paris and rural and small-business work across Lamar County, from our Texarkana team
- Wichita Falls, from our Wichita Falls team, for industrial and home repairs across Wichita and Archer counties
Outside that area, ask and we’ll tell you if we can reach it.
Price your Texas concrete repair project
System, sealer, prep, and the drive cost, all itemized in one quote. It takes about two minutes to go from square feet to a real number.
Frequently asked questions
What does concrete repair and resurfacing cost in Texas?
How does Texas's climate and substrate affect concrete repair longevity?
Can you repair existing slabs on Texas residential and commercial sites?
Which Texas project types and industries use concrete repair most?
Last updated:
Ready to transform your floor?
Get a free, no-obligation quote from our team.
