Skip to main content
Bel Covo
modern sleek onyx polished concrete

Concrete contractor in Holliday, TX

What does concrete flooring cost in Holliday, Texas?

Concrete flooring in Holliday runs the same ranges as the broader Texas market: polished concrete lands in the low-to-mid single digits per square foot, stained and decorative systems fall in the middle, and high-end epoxy or metallic builds reach the top of the range. Slab condition, square footage, and finish selection all move the real number. The regional breakdown below walks through what actually drives a Holliday quote up or down.

Driveways, shop slabs, and floors in Holliday

We’re a concrete contractor in Holliday, TX, about 15 miles southwest of our Wichita Falls team, and we’ve done this work since 2004. Most calls here are a driveway, a shop or barn slab, a garage coating, or a polished floor. Many start as a new pour that gets its coating or polish once the slab cures. On a new slab, we write the pour spec for the finish that goes on it. Get your price now.

Why does Bel Covo serve Holliday?

Holliday sits in northern Archer County, just southwest of Wichita Falls on US-277 and US-82, near Lake Wichita. Our Wichita Falls team already works this stretch, so a job here is a short trip, not a special one.

Most of the work out here is ranch and farm shops, equipment slabs, and home driveways. Now and then it’s a barndominium floor. Our Pour-4-Polish process sets up the slab for its finish from the start. That way a shop slab can take a coating or polish later without waiting on a second outfit.

New pours, coatings, and polish around Holliday

Before we set a price or a start date, we look at four things: how hard the slab will work, where moisture can come from, how much weight rolls across it, and when you need it ready.

What new concrete do we pour?

Driveways and approaches. Holliday’s ground sits on Permian red beds, and the local sand can carry gypsum, a sulfate that eats at concrete, unless it’s washed. So the ground prep gets as much care as the concrete. We pack the subgrade and saw control joints spaced to the slab’s thickness. Our standard driveway quote is a 5 inch slab on a packed gravel base, with rebar, poured with a 4,500 PSI mix. On any bid you compare, check for at least 4,000 PSI. Driveway details.

Shop and barn slabs. Ranch shops, equipment barns, and metal buildings are steady work around Holliday. Those floors carry loads a house garage never sees. So we add rebar, thicken the edges where the overhead doors land, and lay a vapor barrier under any slab that may get a coating or polish later. Shop slab details.

Patios and flatwork. Walks and patios in Holliday sit on the same red-bed soil as the driveways, so they get the same ground prep. The finish is what changes. Patio details.

Which finishes go on a Holliday floor?

Garage floor coatings. We grind the slab down to clean, bare concrete first, then the coating goes on. A family garage usually gets a flake floor, and that runs $8.55 to $10.39 a square foot. A working ranch shop holds up better under a chemical-resistant polyaspartic, the premium build, priced on your quote. Garage floor coatings.

Polished concrete. A barndominium or shop interior that skips tile and carpet can use a polished slab for a clean, hard-wearing floor. We grind the concrete back to pull the shine out of the slab itself. Nothing gets painted or rolled on top. Polished concrete details.

Pour now, coat or polish later

Pour a slab in Holliday now and pick a coating or polish later. You still won't need a second company. Pour-4-Polish puts the pour and the finish in one scope, with one workmanship warranty on the finished slab and one number to call.

What should Holliday owners know about the ground, gravel, and aggregate here?

Most work around Holliday is ranch shops and driveways, where holding up against the ground matters more than looks. The real worry is Permian gypsum buried in the old terrace soil out here. It can attack plain concrete from below.

We handle it the way we handle every pour around Wichita Falls. The coarse rock is Red River terrace gravel, the mix is built to resist sulfate, and crushed limestone comes in from Dolese’s Richards Spur quarry north of Lawton, Oklahoma. If the sand comes from gypsum-bearing Petrolia or Waggoner Ranch terrace stock, we call for Type V cement and an ASTM C1012 test first. That’s a lab test that shows whether the mix holds up to sulfate.

That same red-bed chemistry helps a polished floor. The paste turns a warm, rusty tone, from cream through deep red-brown. And that pink-to-salmon depth pairs well with a brown or amber stain when you want a finished interior.

See what your Holliday floor costs online

Tell us a little about the job, and the quote tool gives you a ballpark price right away. No waiting on a callback.

What moves the cost of concrete in Holliday?

Three things move the number on a Holliday job: the square footage, the condition of any slab you want coated or polished, and the finish you pick. A driveway runs $6.96 to $16.43 a square foot, depending on thickness and finish. Run the online quote tool and you’ll have a ballpark before any phone call. Travel to Holliday shows up as its own line on the quote, not buried in the rate.

Which other Archer County cities does Bel Covo serve?

Our Wichita Falls team also covers Archer City and Lakeside City in Archer County. For any of them, the first 40 road miles each way are free, and the quote tool prices the rest from your address.

What the concrete in Texas is actually made of

The aggregate story in Texas concrete

Most of our Texas work sits in 2 very different aggregate regions (the rock and sand in concrete). Around Texarkana, near the Arkansas line, the cement is made from Annona Chalk and the rock is river gravel. That gives some of the brightest polished concrete in the region. Around Wichita Falls, red rock layers (the Permian red beds) and limestone trucked in from Oklahoma give polished floors a warm desert tint. Our Texas concrete flooring page covers where we work.

Why does Texarkana concrete polish so bright?

It starts with the cement. The Texarkana market makes it from Annona Chalk, a soft, very pure limestone from the Cretaceous. The coarse rock and sand are gravel from the Red River and Little River terraces, and most of it comes across the line from Little River County, Arkansas.

Chalk makes the cement paste bright white, and tan to buff gravel mottles it. A polished floor reads as a warm off-white field, speckled with round quartz and chert pebbles from golden brown to pale gray. Exposed aggregate shows a round, many-colored pebble pattern, not the sharp, broken look of a crushed-limestone pour.

Chalk cement is much whiter than standard gray Portland. So acid stain and dye colors pop brighter here than in the DFW or Oklahoma City metros. It sets a little lighter than most Oklahoma or Texas mixes too, so a floor starts bright even without white cement added. The round gravel looks more decorative than industrial. A broom finish holds its texture well, because the gravel stays down below the grooves.

Watch the chert. The gravel can carry chert bits that polish to a glassy shine and leave patches of uneven sheen, unless the installer densifies hard. The sand is usually a Gulf Coastal Plain blend, high in quartz.

How does Wichita Falls aggregate change the polished floor?

The coarse rock here is gravel from old Red River terraces: quartzite, quartz, and chert, from pebbles up to cobbles. Cement-quality and high-spec crushed stone is Ordovician limestone trucked in from southern Oklahoma. Local Permian sandstone and mudstone (the Petrolia Formation) is too soft for structural concrete. It mostly ends up as fill.

Iron from the red beds in the sand tints the cement paste a warm red. Round quartzite and chert pebbles stud it, cream and tan to deep red-brown. The look is rusty, like a desert floor, and warmer than a standard gray DFW pour. That sand can give concrete a pink to salmon undertone with no pigment. Rush the cure and you can get blotchy white powder (efflorescence).

Gypsum is the big risk. Beds up to 25 feet thick run through the red rock layers, so unwashed local sand can carry sulfate. Sulfate makes concrete swell. It’s the biggest reason polished floors fail here, and it shows up as map cracking and pop-outs months after the pour. Good mixes use washed Red River sand or manufactured sand from Arbuckle limestone.

The pink undertone gives stained polished concrete floors real depth, with brown or amber acid stain most of all. It fights cool gray dyes, though. A broom finish hides the color shifts. Polish shows them, so the whole pour needs sand from one source.

Who supplies aggregate around Texarkana and Wichita Falls?

Ash Grove Cement Company mines the Annona Chalk and makes cement at its plant in Foreman, Arkansas, about 30 miles northeast of Texarkana. SBM Rock in Texarkana is the local crushed stone supplier, from #57 rock to base rock and flex base. In Wichita Falls, Bounds Pit sells local sand, gravel, and crushed limestone. Dolese ships limestone in by rail and truck from its Richards Spur quarry north of Lawton, Oklahoma. Martin Marietta runs portable ready-mix plants in town.

Pouring a slab you’ll polish near Wichita Falls? Ask the plant if the sand is washed Red River or Arbuckle manufactured sand, and if one source will cover the whole pour. Near Texarkana, the chert needs a hard densify, or it polishes to patchy, glassy spots.

What Does Concrete Work in Holliday Look Like?

Polished concrete floor in luxury home entryway reflecting chandelier and modern interior designAction Powersports custom logo embedded in glossy black epoxy showroom floorRound Barn polished concrete floor with mirror-like reflections of windows in dark high-gloss finishPolished charcoal concrete floors in open-plan luxury home with stone fireplace and floating staircasePolished dark concrete floor in restaurant bar area with branded bar stools, tap handles and TVsMetallic epoxy floor in dark amber and brown marble swirl pattern with mirror-like gloss finishMetallic epoxy floor with colorful light-ray inlays at Brady Theatre in performing arts venueExpansive sealed concrete floor in double-height residential great room with French doors and transom windowsLow-angle dramatic view of polished concrete floor in large warehouse with column reflectionsQuarter-sawn wood-plank concrete overlay detail showing realistic grain texture and warm tonesHigh-gloss sealed outdoor concrete slab with mirror-like reflection of a boat trailer in daytimePolished concrete floor in Westmoore Community Church lobby viewed from wider angle

How far will Bel Covo travel to pour concrete in Holliday?

Bel Covo serves Holliday concrete projects within the standard service radius, and our crews are typically 3-6 weeks booked at any given moment. Every quote is itemized to show the cost of each step of the work, including the mobilization that gets equipment on site, so the quote doubles as the order of operations for your project. On accepted work, billing follows those same steps and shows the completion percentage of each as it happens, with nothing buried in a vague lump sum. Call 940-503-3528 for a straight answer in under two minutes.

Which concrete services does Bel Covo offer in Holliday?

Our Holliday crews handle polished concrete, epoxy and polyaspartic coatings, decorative staining, driveways, patios, and repair work. Every job follows the same Pour-4-Polish process and finish discipline used on our flagship projects. The related links below point to the specific service pages that match common Holliday requests.

What questions come up most about Holliday concrete?

Does Bel Covo serve Holliday directly?

Yes. Holliday is inside our North Texas service area, and crews dispatch from our Wichita Falls team. We pour and finish driveways, shop slabs, garage coatings, and polished concrete for Archer County properties.

What does a concrete driveway cost in Holliday?

Holliday driveways run $6.96 to $16.43 a square foot installed, based on thickness, rebar, and finish. A two-car driveway of about 500 square feet runs $3,650 to $8,650 before travel. A small drive runs a bit above the per-foot range, since setup spreads over fewer feet. The online quote tool prices your own job.

Can you pour and coat a garage floor in the same scope?

Yes. Our Pour-4-Polish process plans the pour, the cure time, and the coating as one scope of work. You get one schedule and one workmanship warranty on the finished floor.

Is Holliday too small or too far for Bel Covo?

No. Holliday and the rest of Archer County are part of our regular North Texas service area. Rural shops, barndominiums, ranch and farm slabs, and lake-area builds are core work for us, not exceptions.

Last updated:

Ready to transform your floor?

Get a free, no-obligation quote for your project.

Archer County, Texas

See concrete work across Archer County, Texas →