- Concrete Craftsmen Since 2004
- NW & Eastern Arkansas Coverage
- Slabs Built for the Finish
- On-Site Moisture Testing
What does epoxy flooring cost in Arkansas?
Epoxy flooring cost in Arkansas runs $6.08 to $10.17 a square foot installed for our quartz and metallic floors. A two-car garage of about 450 square feet runs $4,000 to $4,900 with our flake floor, before the drive cost (our trip out to your site). A small floor runs above the per-foot range, since setup spreads over fewer feet. Our rate is the same in Siloam Springs as in Jonesboro.
| Project Type | Typical Size | Installed Cost Range |
|---|---|---|
| 1-car garage or shop bay | 200 to 250 sf | $2,100 to $2,550 at 225 sf |
| 2-car residential garage | 400 to 500 sf | $4,000 to $4,900 at 450 sf |
| 3-car or oversized garage | 600 to 750 sf | $6,100 to $7,450 at 700 sf |
| Detached shop / barndo bay | 800 to 1,200 sf | $8,650 to $10,500 at 1,000 sf |
| Delta industrial / processing | 1,500 to 4,000 sf | Quoted by spec |
Each total is our flake floor before the drive cost. The low end is a clean, dry slab, and the high end adds a moisture barrier primer. Old coating removal and structural repair price on their own lines. For flake and other garage systems side by side, see the Arkansas garage floor coating cost page.
The system and the slab move an Arkansas epoxy price the most. The floor’s size and the drive move it too. The town doesn’t. Start with the system. Metallic prices lowest on our list, then quartz, then flake. A commercial high-build floor tops it. Then the slab. Slabs made with Ozark Boone Formation limestone usually grind clean. Delta slabs sit on Mississippi River gravel over expansive clay, the kind that swells, and that brings more moisture and crack prep.
Arkansas epoxy flooring cost by system type
Our flake, quartz, and metallic floors are built on 100 percent solids epoxy, not the 40 to 50 percent solids in a store kit.
| System Type | Cost per SF | Best For |
|---|---|---|
| Solid-color polyaspartic | Quoted by spec | Shop bays, utility spaces, budget-driven garages |
| Flake broadcast with urethane topcoat | From $8.46 | Most NWA and river-valley residential garages |
| Metallic epoxy with clear urethane topcoat | From $5.96 | Bentonville showrooms, corporate display floors, executive garages |
| Quartz broadcast with chemical-resistant topcoat | From $8.17 | Wet-condition residential, light Delta industrial, washdown bays |
| Commercial high-build chemical-resistant | Quoted by spec | Processing plants, washdown rooms, forklift-traffic warehouse floors |
The range above includes setup. A single rate can sit a little under it. We price solid-color and high-build floors per job, once we know what the floor has to stand up to.
Inside each tier, the slab sets the rate. A fresh Benton County barndominium pour needs only an ICRI CSP 3 grind, a rough profile the coating can grip. A pre-1990 slab in downtown Little Rock with a failed coating or oil soaked in costs more to prep.
Does your part of Arkansas change the price?
Not the rate per foot. What changes is which team comes and what kind of floor we tend to find.
| Corridor | Cities | Typical Band (per SF) | Dispatch / Mobilization |
|---|---|---|---|
| NW Arkansas (I-49) | Fayetteville, Bentonville, Rogers, Springdale, Siloam Springs | $6.08 to $10.17 | Our NW Arkansas team |
| Eastern Arkansas / Delta (I-40) | West Memphis, Forrest City, Jonesboro, Paragould | $6.08 to $10.17 | Our Eastern Arkansas team; our Memphis team for West Memphis and Paragould |
| Texarkana and southwest Arkansas | Texarkana, Hot Springs, Arkadelphia | $6.08 to $10.17 | Our Texarkana team |
The I-49 corridor brings the most decorative work. Showrooms around Rogers, Lowell, and Bella Vista want metallic and flake floors. Ozark barndominium builds usually get a flake garage. Epoxy flooring in Siloam Springs comes from our NW Arkansas team, same as Bentonville.
The jobs split between small Delta barndo garages and big processing and distribution floors, and the big ones need high-build, chemical-resistant specs.
Around Texarkana, most of the work is home garages. Hot Springs sits about 130 miles from our Texarkana team, so smaller jobs there often pair with nearby work.
What affects epoxy flooring cost in Arkansas?
Surface prep. This is the biggest line on most quotes. A slab with a vapor barrier on record needs only our standard grind. Older buildings in downtown Fayetteville, Springdale, or Hot Springs may have old glue or tile mastic. That has to come off first. So may pre-1980 Delta slabs in Crittenden County.
Slab geology. Boone chert grinds faster than the limestone around it, so the primer sometimes fills pinholes. In the Delta, expansive clay that swells under the slab opens hairline cracks. We fill those with epoxy mortar before we coat. Around Texarkana, slabs poured with Annona Chalk binder and Red River gravel behave, and rarely need more than our standard grind.
Square footage. Bigger floors cost less per foot, since setup and the drive spread out. A 200 square foot laundry room runs higher per foot than a 4,000 square foot Delta warehouse.
The system. Metallic, quartz, and flake each carry their own rate. Multi-color metallic work takes a practiced hand, so it prices toward the top of its range.
Moisture. Delta humidity runs above 70 percent for months, and older slabs across the state pass more moisture. When a slab raises a flag, we run an ASTM F1869 calcium chloride test and an ASTM F2170 probe before prep. Above 3 pounds, a moisture barrier primer adds $1.80 a square foot.
The drive. Crews come from the nearest team. The drive is its own line, and the online quote tool works it out from your address.
The bargain epoxy quote in Arkansas
A bid far under our range usually means a cheap kit, an acid wash instead of a diamond grind, no moisture check, and no real topcoat. That film lifts within two seasons here, and you pay to coat the floor twice. The checklist at the bottom of this page shows what to ask.
Why does the topcoat matter so much in Arkansas?
Sun is the first reason. From June through September the UV index hits 9 to 10. Sunlight breaks plain epoxy down, so it yellows within 6 to 18 months, worst by a south- or west-facing garage door. A clear topcoat is made to take that sun. Our flake floors get a 4 mil urethane top over the epoxy, and our metallic floors get a clear urethane topcoat.
Heat is the second. Polyaspartic, our premium flake build, stays hard past 200 F. Epoxy softens near 130 F, and that’s when hot tires lift it. Cold is the third. The NW Ozark plateau sees 80 or more freeze-thaw cycles a winter, and rigid epoxy can crack at the saw-cut joints. The Delta sees 50 to 60, and its humidity runs above 70 percent for months. Our polyaspartic vs epoxy garage floor post puts the two side by side.
How do you get an accurate Arkansas epoxy flooring quote?
The quickest way is the online quote tool, which takes about two minutes. Put in the floor size, the address, the system, and the shape the slab is in. You get an installed price, with the drive on its own line. Some floors need a visit first: Delta processing floors, washdown rooms, or a slab that needs a moisture test. For those, it sets up an on-site look at no charge.
See what your Arkansas epoxy floor costs
Put in your floor size and address. You get a real number for the system you pick. The drive from the nearest Arkansas team is on it, and so is a moisture barrier primer if your slab needs one.
Why do quality Arkansas epoxy installations cost more?
Because a sound job does four things a cheap one skips. Before you sign any bid, ours included, ask about each one:
- How do you prep? The answer should be a diamond grind to CSP 3. Acid-etch shortcuts lift inside two years, and on chert-heavy Boone slabs the acid can’t open up the chert at all.
- What’s the percent solids on the data sheet? 100 percent solids epoxy cures to 20-plus mils. A 40 to 50 percent solids kit cures to 3 to 5.
- What did the moisture check show? When the slab raises a flag, the test comes before the base coat. Skip it on a Delta slab above 3 pounds, and blisters show up within one humid season.
- What’s the topcoat? Arkansas sun and Ozark freeze-thaw both call for one. Plain epoxy alone is wrong for any floor here that sees the sun.
If a bidder can’t answer all four, the low number is the expensive one.
Related pages
- Epoxy flooring in Arkansas: the service and how we do it
- Arkansas state hub
- Garage floor coating cost in Arkansas: garage systems side by side
- Polished concrete cost in Arkansas: the other finish
- National epoxy flooring cost: system tiers compared
- Build a price estimate
Pricing in Arkansas
In Arkansas, most projects range from $6.08 to $10.17 per square foot. Final cost depends on floor condition, area size, and finish selection.
Get your custom quoteFrequently asked questions
How much does epoxy flooring cost in Arkansas?
Why does epoxy flooring price differently across Arkansas corridors?
Does Arkansas geology change what an epoxy floor costs?
How does Arkansas humidity and freeze-thaw affect epoxy longevity?
What does a Bel Covo Arkansas epoxy flooring quote include?
Last updated:
Ready to transform your floor?
Get a free, no-obligation quote from our team.
