Skip to main content
Bel Covo
modern sleek onyx polished concrete

Concrete contractor in Texarkana, AR

What does concrete flooring cost in Texarkana, Arkansas?

Concrete flooring in Texarkana runs the same ranges as the broader Arkansas market: polished concrete lands in the low-to-mid single digits per square foot, stained and decorative systems fall in the middle, and high-end epoxy or metallic builds reach the top of the range. Slab condition, square footage, and finish selection all move the real number. The regional breakdown below walks through what actually drives a Texarkana quote up or down.

Concrete work in Texarkana

When you call a concrete contractor in Texarkana, AR, the floor usually sits somewhere in the town’s cross-state freight business. It might be a warehouse off I-30, a supplier shop for one of the big plants, a Miller County barndominium, or a downtown building getting a second life along State Line Avenue. Our Texarkana team pours, polishes, and coats all four.

How does Texarkana function as a cross-state region?

Texarkana is one of the few towns where the state line runs right through downtown. State Line Avenue is the boundary. The Arkansas side, about 29,000 people, is in Miller County. The Texas side is in Bowie County, and one freight economy runs across both. An Arkansas-side job and a Texas-side job get the same craft and the same crews from our Texarkana team.

What floors does the Four States freight and industrial base need?

Texarkana sits at the elbow of the Four States region: Arkansas, Texas, Louisiana, and Oklahoma. I-30 runs through as the freight route between Dallas and Little Rock, and US-59 and US-67 carry traffic north. Big plants, smaller fabrication shops, and freight yards along I-30 drive the plant floor work on both sides of the line.

Floor specs here look more like Fort Smith plant work than anything else in southern Arkansas. Most builds pull from a short list:

  • Urethane cement at 1/4 inch, for thermal shock (fast swings from hot to cold) and pH-12 washdown
  • 100 percent solids epoxy at 20 to 30 mils, for forklifts and chemicals
  • Polyaspartic topcoats, where you need the floor back over a weekend
  • Polished concrete, for the offices inside the same building

We grind the slab to a CSP 3 to 5 profile. That’s the ICRI CSP scale you’ll see on bids, and it tells you how rough the surface is left so the coating can grip. We check every slab. When the check shows a warning sign, or you ask, we run a moisture test per ASTM F1869. Urethane cement is priced per job once we’ve seen the floor. Heavy epoxy and polyaspartic floors run $6.08 to $10.17 a square foot. See the Arkansas polished concrete cost guide.

What is the local stone and subgrade under Southwest Arkansas barndominium country?

Southwest Arkansas soil changes from one lot to the next. Bottomland near the Red River holds clay the river laid down (alluvial clay), and it moves as the seasons get wet and dry. Upland ridges have thin topsoil over iron-rich clay. Cleared timber land still has old stump holes and skidder ruts, and those pack down unevenly. A lot of pads have two or three of these inside one footprint. So we check how well the ground holds weight at several spots before we pour, then adjust the packing and the base rock to match. The base rock comes from close by: SBM Rock - Texarkana runs a crushed stone quarry about a mile from town.

Slab spec for Miller, Little River, and Lafayette county builds

Miller, Little River, and Lafayette counties have some of the cheapest rural acreage within reach of a metro in southern Arkansas. A barndominium here usually gets a 5 to 6 inch slab, with welded wire or a rebar mat per the spec. A vapor barrier goes on the ground, and the control joints are placed to steer cracks away from the finished areas. The slab runs $5.32 to $15.61 a square foot. See Arkansas concrete flatwork. Polishing that floor runs $3.83 to $6.25 a square foot, depending on the shine and how much stone shows.

What does downtown reuse on the state line take?

Downtown Texarkana is coming back on both sides of State Line Avenue. Early 1900s stores and warehouses are turning into restaurants, breweries, offices, and apartments over shops. Builders call it adaptive reuse. A lot of those slabs are pre-war, with old tile glue, no moisture history anyone can read, and patchy cold joints. An old slab like that is a warning sign by itself. Before we polish one, the prep usually goes like this:

  1. A moisture test per ASTM F1869 at three or more spots
  2. Grinding to CSP 3 to get the old tile glue off
  3. Fixing the joints and routing out cracks before the grind passes start
  4. A grind-and-seal finish when the old concrete was never meant to be a finished floor

What about residential garage floor coatings?

A full flake polyaspartic floor over a 20-plus mil epoxy body runs $8.55 to $10.39 a square foot. It cures fast, so a Friday install is usually ready to park on by the weekend. See Arkansas garage floor coatings for system detail. Pouring new? With Pour-4-Polish, we write the pour spec for the floor that goes on it.

Spec to the failure mode

A plant supplier shop fails in different ways than a downtown brewery, and both differ from a Miller County barndominium. Fast hot-to-cold swings crack ordinary epoxy. Harsh cleaners can lift polyaspartic off the slab. Forklift hits tear up both. We walk the space, find what's most likely to wreck your floor, and spec urethane cement, 100 percent solids epoxy, or polished concrete to match.

How does Texarkana’s climate affect exterior work?

Texarkana sits in USDA Hardiness Zone 8a, with milder winters than Fayetteville or Little Rock. The freeze-thaw swing is small next to northern Arkansas, so outdoor aprons, driveways, and patios take less stress over a year. We still usually spec air-entrained concrete, which has tiny air bubbles that give freezing water room, and a penetrating sealer on driveways and parking aprons that see freezes.

See what your Texarkana project costs

Enter your project details and square footage. The quote tool lists the drive to your address as its own line, so the price shows your real travel cost.

Nearby southern and central Arkansas cities we work in

We also do Arkansas polished concrete and Arkansas concrete flatwork across the Four States region.

What the concrete in Arkansas is actually made of

The aggregate story in Arkansas concrete

Arkansas has two kinds of concrete rock, and a polished floor shows which one you got. The northwest Ozarks run on Boone Formation limestone, with 15-30% chert in some Benton County pits. The Delta runs on Mississippi River gravel. The two floors differ so much in color, texture, and how they take a finish that they might as well be in two states.

Northwest cities we cover, like Fayetteville and Fort Smith, are on the Arkansas concrete flooring hub.

What aggregate drives northwest Arkansas polished floors?

Northwest Arkansas runs on Boone Formation limestone (Mississippian age). That stone carries a lot of chert, a hard rock made of silica. Crushed Boone stone goes into structural concrete. Most metro mixes get their sand and gravel from river bars in the White River drainage. Sandstone from the Atoka and Bloyd formations shows up too, but only as a second source in some rural Benton and Carroll County pours.

Polished, these floors read as a light warm gray with a cream-to-bone tint. Off-white and buff-tan chert spots break it up. How many spots you get depends on which pit the ready-mix plant pulled from on pour day. At our standard cut, the floor shows a salt-and-pepper look. Cut deeper, to medium or full aggregate exposure, and it turns into a mottled field with bits of fossil in it. Fossil crinoid stems, the Boone’s best-known mark, show up as small pale disks.

Why does Boone chert leave pinholes in a polished floor?

Porous chert is the headache. The Boone holds lumps of chert, and some are full of tiny holes while some aren’t. Arkansas Geological Survey papers name them as a cause of past quarry problems. In a polished floor, that porous chert grinds faster than the stone around it. That leaves pinholes, dull spots, or pop-outs at the surface, and no amount of densifier fixes them after the fact.

Northwest Arkansas aggregate suppliers include the APAC-Central McClinton-Anchor quarries in Springdale, Hindsville, and Gravette. APAC Valley Springs in Harrison is a second supplier.

Boone stone polishes bright. Acid stains take well on it in earth tones and warm grays. Chert-heavy mixes take stain in patches, because silica doesn’t react with the stain, so a stained floor shows the chert as light freckles on darker stone. Broom finishes look clean and gray. Exposed-aggregate finishes look good here, since you can see both the fossils and the chert.

How does Delta gravel change what a polished floor looks like?

The Delta runs on sand and gravel the Mississippi River laid down, and the coarse rock in it is mostly chert and quartz pebbles. There’s some sandstone, novaculite, and milky vein quartz mixed in, all worn down from older Paleozoic bedrock upstream. There’s next to no local limestone quarry. So crushed stone for the main mixes gets hauled in from Batesville (Independence County) and the Little Rock quarry belt. For jobs in eastern Crittenden County, it comes from Memphis-area plants.

Polished, these floors read warm tan to buff. Cut to the stone, you see creamy cement paste broken up by round chert pebbles from pea-size to marble-size. They come in white, amber, honey, and gray, and now and then you get a rose-red jasper. The whole floor looks warmer and busier than a crushed-limestone floor from northwest Arkansas or southwest Missouri.

What does Delta gravel mean for cracking, stain, and finish?

Round river gravel leaves pebble outlines you can see at a medium or full cut. Some clients love that look. Others call it busy. Some beds of chert-heavy river gravel can also cause alkali-silica reaction, or ASR. That’s when silica in the rock reacts with the cement and swells, which leads to map cracks and pop-outs. Good Delta ready-mix plants guard against it with Class F fly ash. A slab poured with imported rock of unknown origin still carries ASR risk. Still, the expansive clay under Delta slabs is a bigger risk than the rock.

Delta aggregate and ready-mix suppliers include Arkansas Concrete Company, with plants in Forrest City, Wynne, Brinkley, Marianna, and Helena. Others are Razorback Concrete Company (West Memphis, with more than 15 plants), and Forrest City Ready-Mixed Concrete Co.

At a medium cut, a polished Delta-gravel slab has a lot of life. Round pebbles catch light in a way sharp crushed stone doesn’t. Stain goes on in patches. The cement paste takes acid stain fine, but chert pebbles don’t, so the stain makes the contrast stronger. Broom finishes look fairly clean, since the fine sand is rich in quartz. For an even color without the native gravel, the usual Delta choices are epoxy coating over a prepped slab, a self-leveling overlay, or grind-and-seal.

What Does Concrete Work in Texarkana Look Like?

Polished concrete floor in luxury home entryway reflecting chandelier and modern interior designAction Powersports custom logo embedded in glossy black epoxy showroom floorRound Barn polished concrete floor with mirror-like reflections of windows in dark high-gloss finishPolished charcoal concrete floors in open-plan luxury home with stone fireplace and floating staircasePolished dark concrete floor in restaurant bar area with branded bar stools, tap handles and TVsMetallic epoxy floor in dark amber and brown marble swirl pattern with mirror-like gloss finishMetallic epoxy floor with colorful light-ray inlays at Brady Theatre in performing arts venueExpansive sealed concrete floor in double-height residential great room with French doors and transom windowsLow-angle dramatic view of polished concrete floor in large warehouse with column reflectionsQuarter-sawn wood-plank concrete overlay detail showing realistic grain texture and warm tonesHigh-gloss sealed outdoor concrete slab with mirror-like reflection of a boat trailer in daytimePolished concrete floor in Westmoore Community Church lobby viewed from wider angle

How far will Bel Covo travel to pour concrete in Texarkana?

Bel Covo serves Texarkana concrete projects within the standard service radius, and our crews are typically 3-6 weeks booked at any given moment. Every quote is itemized to show the cost of each step of the work, including the mobilization that gets equipment on site, so the quote doubles as the order of operations for your project. On accepted work, billing follows those same steps and shows the completion percentage of each as it happens, with nothing buried in a vague lump sum. Call 903-403-3528 for a straight answer in under two minutes.

Which concrete services does Bel Covo offer in Texarkana?

Our Texarkana crews handle polished concrete, epoxy and polyaspartic coatings, decorative staining, driveways, patios, and repair work. Every job follows the same Pour-4-Polish process and finish discipline used on our flagship projects. The related links below point to the specific service pages that match common Texarkana requests.

What questions come up most about Texarkana concrete?

How is Texarkana, Arkansas covered?

Our Texarkana team covers Miller County and the Arkansas side of town, the same as the Texas side of State Line Avenue. Work here is a short day trip for the crew, not a long haul. The drive still shows as its own line on every quote, figured from the real distance to your address.

What concrete services do you provide in Texarkana?

We polish concrete for stores and freight buildings, do plant and industrial floor coatings for factories and distribution centers along I-30, polish barndominium floors on Miller County acreage, and coat garage floors in home shops. That covers diamond grinding from 30 grit up to 3000, urethane cement and 100 percent solids epoxy, and a moisture test (ASTM F1869) when the slab shows a warning sign or you ask for one. We also pour barndominium slabs in one pour, with the shop side and the living side handled under one contract.

Do you work jobs that span the Arkansas and Texas sides of Texarkana?

Yes. Our Texarkana coverage runs across both sides of State Line Avenue under one quote, so a job that straddles the line doesn't need a second contractor. The scope, the schedule, and the finish stay the same whether the lot sits in Miller County, Arkansas or Bowie County, Texas.

How much does a concrete floor cost in Texarkana?

On the Arkansas side of Texarkana, polished concrete runs $3.83 to $6.25 a square foot, depending on the shine and how much stone shows. A full flake polyaspartic floor over epoxy runs $8.55 to $10.39 a square foot. Barndominium slabs run $5.32 to $15.61 a square foot. Urethane cement for plant floors is priced per job, because we price it after we see the floor. The drive is its own line on every quote, figured from the real distance to your address.

Last updated:

Ready to transform your floor?

Get a free, no-obligation quote for your project.

Miller County, Arkansas

See concrete work across Miller County, Arkansas →