Skip to main content
Bel Covo
modern sleek onyx polished concrete

Concrete contractor in Fulton, MS

What does concrete flooring cost in Fulton, Mississippi?

Concrete flooring in Fulton runs the same ranges as the broader Mississippi market: polished concrete lands in the low-to-mid single digits per square foot, stained and decorative systems fall in the middle, and high-end epoxy or metallic builds reach the top of the range. Slab condition, square footage, and finish selection all move the real number. The regional breakdown below walks through what actually drives a Fulton quote up or down.

Concrete work in Fulton

We’re a concrete contractor in Fulton, MS, about 22 miles east of our North Mississippi team. Fulton is the Itawamba County seat. Our work here runs from home driveways to industrial slabs near Port Itawamba, on the Tennessee-Tombigbee Waterway. We pour new concrete, and we coat or polish slabs that are already down. Get a price in 2 minutes.

The county seat has about as much commercial work as home work: county buildings, supplier-park pads, retail slabs, and the warehouse and plant floors the port draws. For industrial concrete flooring in this part of Mississippi, we build slabs for forklift and rack loads, with thicker edges at the door openings and a joint layout sized to the traffic.

What aggregate and subgrade does Fulton concrete sit on?

Fulton slabs sit on chert gravel from the Coastal Plain. The subgrade, the ground right under the slab, is old river terrace soil. It was laid down before the loess, a wind-blown silt, came in. Geologists call it pre-loess Pleistocene terrace deposits. It comes in layers and holds water. Packed poorly, it shrinks in dry months and swells in wet ones, and that shows up as cracked joints and lifted slab edges within a few years.

So the ground comes first. We run a loaded truck over the base to find soft spots (a proof-roll). Then we pack it to 95% Proctor, meaning 95 percent as tight as a lab test says that soil can get, and pour. Any slab that will get a coating or a polish later also gets a vapor barrier under it.

Chert from the Tuscaloosa Gravels, not limestone

Northeast Mississippi concrete uses chert from the Tuscaloosa Gravels, not the crushed limestone you’d see in hard-rock country. The APAC Mississippi - Tremont Pit in Itawamba County supplies sand and gravel close by. B & B Concrete Co - Fulton Plant runs a ready-mix plant right in town, so most pours here show up without a long haul.

Chert is harder and more angular than most limestone, and it holds its edges when we grind it with diamonds. Its color is what you see on a polished floor: a warm beige cream with scattered tan and rust flecks, not the bright white rock of granite country.

Chert also varies more from load to load than hard rock. On a big polished floor laid in several pours, ask for every load from one pit. And make sure the mix guards against ASR (alkali-silica reaction), where some chert reacts with the cement and cracks the slab over time. That keeps color and strength even across the floor.

Check for moisture before any coating

Itawamba County's terrace soils hold water close to the surface. We diamond grind every slab before epoxy or polyaspartic goes on, and we check it for moisture. If the check shows a warning sign, we test it and add a moisture barrier primer when the reading calls for one. Moisture from below is a top reason garage coatings fail here.

What concrete services does our North Mississippi team bring to Fulton?

Driveways and approaches. Our driveway quote is a 5-inch slab on a packed gravel base, with rebar, poured with a 4,500 PSI mix. We space the control joints to the slab’s thickness. Driveway details.

Shop, barn, and commercial slabs. Equipment, shop, and barn slabs get the same thicker door edges and traffic-sized joints. They also get a vapor barrier where a coating will follow. Shop slab details.

Patios and flatwork. Patios get the same packed, proof-rolled base. We pour at 4,000 PSI and finish the top to the texture you want. Patio details.

Coatings and polish

Garage floor coatings. A chip-broadcast floor, with colored flakes in the resin, fits most homes. For a working shop or a commercial bay near the waterway, a polyaspartic that holds up to chemicals is the better pick. Garage floor coatings.

Polished concrete. Polish fits Fulton barndominiums and commercial interiors, where the owner wants a tough floor that’s easy to clean, with no carpet or tile. The shine and the rock you see are ground into the slab itself. Polished concrete details.

How much does concrete flooring cost in Fulton?

New pours in Fulton, a driveway or a slab, run $5.32 to $15.61 a square foot. A two-car driveway of about 500 square feet runs $3,650 to $8,650 before the drive cost. A driveway carries a gravel base and rebar that a plain slab may not. And on a small job, setup spreads over fewer feet, so the total can run above the per-foot range. Coatings and polish depend on the size, the slab’s condition, and the system you pick. The online quote tool prices your job in about 2 minutes. The drive cost, our trip to your site, shows before you commit.

See what your Fulton project costs

Answer a few questions and see your price, with no callback needed. The drive to your Fulton address shows on its own line.

Which other Itawamba County cities does Bel Covo serve?

Our North Mississippi team sits about 22 miles west of Fulton and works all over Itawamba County, Mantachie included. The Mississippi service area page shows the rest of our coverage.

What the concrete in Mississippi is actually made of

The aggregate story in north Mississippi concrete

North Mississippi concrete, in the Tupelo and Oxford markets, runs on local chert gravel plus limestone hauled in from out of state. No one quarries commercial-grade limestone in the area. The local rock is Coastal Plain chert gravel and sand. It comes from the Tuscaloosa Gravels and from Pleistocene river terraces older than the loess, along the Mississippi-Alabama line from Tishomingo through Lowndes County. The closest limestone quarries sit 1 to 2 hours away, in Alabama or north-central Mississippi.

Our Mississippi concrete flooring hub lists the north Mississippi cities we serve.

Where does north Mississippi aggregate actually come from?

Crushed limestone comes in by truck or rail. Most of it is from north Alabama, out of the Fort Payne Formation at quarries like Vulcan Materials’ Fort Payne Quarry, and some comes from central Tennessee. Distance costs money. That haul shows up in the concrete price, unlike in states with hard rock close by.

The cement comes from outside too, from plants in Alabama, Tennessee, or Missouri. Lowndes County had its own cement plant, Holcim’s Artesia plant, until Holcim mothballed it in 2009 and quit making cement there for good in 2011. Amrize has owned the site since Holcim spun it off in 2025.

Rogers Group’s yard at the Port of Columbus, in Lowndes County, takes in crushed limestone by barge. None of it comes out of the ground there. Foley Materials’ Columbus Quarry sells sand, gravel, and railroad ballast across the Southeast. And APAC Mississippi runs an MDOT-approved gravel pit at Tremont.

How does the imported-aggregate mix affect polished floors?

A polished floor here reads light gray to warm beige cream, with scattered tan and rust flecks of chert. Source matters. A mix heavy on Alabama or Tennessee limestone polishes to a cleaner, more even pale gray. One heavy on Tuscaloosa chert gravel shows more color change and a warmer tone.

The coarse rock travels far and comes from several competing sources, not one quarry face. So mixes here change more from pour to pour than where hard rock is close. If you want a polished concrete finish to match across slabs poured on different days, the spec should name one source pit before the first pour. Chert-heavy gravel polishes with an earth-tone speckle. Deeply weathered chert can cause pop-outs, small chips that break loose from the surface, so polished work should call for dense, washed chert. Tuscaloosa chert can also react with the cement and crack the slab from inside. That’s called alkali-silica reaction (ASR). The answer is ASTM C1260/C1567 testing on the local chert, at least 20 percent Class F fly ash or at least 25 percent slag, and low-alkali cement (Na2Oeq at or under 0.60 percent). Stain comes out mottled and natural-looking instead of even, much like it does on Memphis concrete. Plan for that. Broom finishes are simple, and local crews know them well.

What Does Concrete Work in Fulton Look Like?

Polished concrete floor in luxury home entryway reflecting chandelier and modern interior designAction Powersports custom logo embedded in glossy black epoxy showroom floorRound Barn polished concrete floor with mirror-like reflections of windows in dark high-gloss finishPolished charcoal concrete floors in open-plan luxury home with stone fireplace and floating staircasePolished dark concrete floor in restaurant bar area with branded bar stools, tap handles and TVsMetallic epoxy floor in dark amber and brown marble swirl pattern with mirror-like gloss finishMetallic epoxy floor with colorful light-ray inlays at Brady Theatre in performing arts venueExpansive sealed concrete floor in double-height residential great room with French doors and transom windowsLow-angle dramatic view of polished concrete floor in large warehouse with column reflectionsQuarter-sawn wood-plank concrete overlay detail showing realistic grain texture and warm tonesHigh-gloss sealed outdoor concrete slab with mirror-like reflection of a boat trailer in daytimePolished concrete floor in Westmoore Community Church lobby viewed from wider angle

How far will Bel Covo travel to pour concrete in Fulton?

Bel Covo serves Fulton concrete projects within the standard service radius, and our crews are typically 3-6 weeks booked at any given moment. Every quote is itemized to show the cost of each step of the work, including the mobilization that gets equipment on site, so the quote doubles as the order of operations for your project. On accepted work, billing follows those same steps and shows the completion percentage of each as it happens, with nothing buried in a vague lump sum. Call 662-356-3528 for a straight answer in under two minutes.

Which concrete services does Bel Covo offer in Fulton?

Our Fulton crews handle polished concrete, epoxy and polyaspartic coatings, decorative staining, driveways, patios, and repair work. Every job follows the same Pour-4-Polish process and finish discipline used on our flagship projects. The related links below point to the specific service pages that match common Fulton requests.

What questions come up most about Fulton concrete?

Does Bel Covo serve Fulton directly?

Yes. Fulton is inside our North Mississippi service area. Our North Mississippi team pours driveways and shop slabs, and coats and polishes floors, all over Itawamba County.

What does a concrete driveway cost in Fulton?

A Fulton driveway runs $6.96 to $16.43 a square foot installed, based on thickness, steel, and finish. A two-car driveway, about 500 square feet, runs $3,650 to $8,650 before the drive cost. A small driveway runs above the per-foot range, since setup spreads over fewer feet. The online quote tool prices your own driveway.

Can you pour and coat a garage floor in the same scope?

Yes. With Pour-4-Polish, we write the pour spec for the coating that goes on it. So the pour, the wait while it cures, and the coating all run on one plan and one schedule.

Is Fulton too small or too far for Bel Covo?

No. Fulton is about 22 miles east of our North Mississippi team, well inside our regular service area. Commercial flatwork in the county seat, industrial slabs near the waterway, and shop and barn slabs out in the county are everyday work for us.

Last updated:

Ready to transform your floor?

Get a free, no-obligation quote for your project.

Itawamba County, Mississippi

See concrete work across Itawamba County, Mississippi →