Skip to main content
Bel Covo
modern sleek onyx polished concrete

Concrete contractor in Olive Branch, MS

What does concrete flooring cost in Olive Branch, Mississippi?

Concrete flooring in Olive Branch runs the same ranges as the broader Mississippi market: polished concrete lands in the low-to-mid single digits per square foot, stained and decorative systems fall in the middle, and high-end epoxy or metallic builds reach the top of the range. Slab condition, square footage, and finish selection all move the real number. The regional breakdown below walks through what actually drives a Olive Branch quote up or down.

A distribution hub on the Memphis airport’s doorstep

Olive Branch grew up next to the Memphis air-cargo hub, and about 36,000 people live here now. For a concrete contractor in Olive Branch, MS, that means two kinds of work: big warehouse and distribution floors on the business side, and garages and interiors in the subdivisions off Goodman Road on the home side. Both need a floor matched to what rolls across it. Get your price now.

Why do distribution floors set the tone in Olive Branch?

They run all day, and that sets Olive Branch apart from the more retail-driven suburbs to the west. The warehouse slabs around Olive Branch carry forklifts, pallet jacks, and turret trucks, often around the clock. A floor like that has to fight wear and hold down dust, and it can’t wear a film on top that chips and peels under a wheel.

Polished concrete with a lithium hardener does that job. The hardener soaks in and makes the top of the slab denser, so the slab itself carries the load and sheds less dust. The shine bounces light around too, which cuts lighting cost across a big floor. Where a warehouse handles chemicals or wet work, we switch to a 100 percent solids epoxy with a broadcast aggregate for grip. Either way, we joint and reinforce the slab to your real rack and forklift loads, not to a stock warehouse spec. See polished concrete details.

Joints wear out first on a warehouse floor

A loaded forklift wheel that hits a bare control joint chips the edge a little more on every pass. Within a year, the joints in a busy Olive Branch aisle have turned into a repair line in the budget. The mix matters, and ready-mix here comes from regional plants like the B & B Concrete Co - Holly Springs Plant over in Marshall County. But the joint detail matters more, so we build it in three steps:

  1. We saw the control joints early, usually within the first day after the pour, and cut them to the right depth.
  2. We fill them with a hard epoxy filler rated for hard wheels, not a soft sealant.
  3. We armor the construction joints where the heaviest loads cross.

The American Concrete Institute guide ACI 302.1R sets the joint spacing and the filler choice. We build to it, because following it is the difference between a 20-year floor and a five-year one.

Which garage floor specs fit Olive Branch, and what do they cost?

Garage flooring is the steady home job in Olive Branch. Our flake floor, RESA Flake, runs $8.55 to $10.39 a square foot, and that range is the epoxy build. We grind the slab, prime it, throw colored flake into the next coat until it won’t take any more, and seal it with clear coats. Epoxy is best indoors. If your garage faces the sun, or you park hot tires on it, we steer you to the polyaspartic build, which cures fast and won’t let a hot tire peel it up. We price that one on your quote. See garage floor coatings for both.

Inside the house, polished concrete gives you a floor with nothing on top to peel. Outside, we pour concrete driveways and concrete patios. A new slab that will be polished or coated goes through our Pour-4-Polish process, and we set the pour spec around the floor that will sit on top.

What should Olive Branch owners know about DeSoto County aggregate and subgrade?

Two things: water coming up from below, and a base that can shift. Olive Branch is humid, and summer dewpoints sit in the low 70s. That pushes water vapor up through any slab poured on the ground, and a coating on top has to live with it.

We check every slab. When a warehouse or garage slab has an unclear moisture history, we test it with a calcium chloride kit (ASTM F1869) or a humidity probe before we pick a coating that forms a film. If the test reads over 3 pounds, an epoxy moisture barrier goes down first, or we move you to a finish that breathes.

Loess, the fine wind-blown silt found across DeSoto County, packs well. Under a thin base, though, it pumps, which means it shifts each time a heavy load rolls over. So we lay a graded aggregate base and pack it to 95 percent Proctor density before the pour. Proctor is the lab test for how tightly a base is packed.

Match the joint filler to the wheel load

On an Olive Branch distribution floor, the joint filler decides how the slab ages. We ask about wheel type and traffic at the quote stage, so we can spec a hard epoxy filler rated for hard wheels. A soft sealant fails at the joints first.

How does Olive Branch pricing come together on the quote?

Square footage, prep, and the system you pick set the number. A polished warehouse floor runs $3.83 to $6.25 a square foot at scale, and an epoxy system for a floor that sees chemicals runs $6.08 to $10.17. The quote tool builds your number from your address and your floor. No phone tag. No “we’ll call you back with a number.”

See what your Olive Branch floor costs online

Enter your square footage and project address. The calculator returns a detailed estimate with materials, labor, and travel included.

Which DeSoto County cities does Bel Covo cover near Olive Branch?

Olive Branch is one of several DeSoto County towns we cover. Southaven sits about 12 miles west, and Horn Lake is farther west on I-55. Hernando lies to the southwest. Down I-55 in Tate County, we cover Coldwater, and to the east we take Marshall County jobs toward Holly Springs. See our Mississippi state hub and the national locations index.

What the concrete in Mississippi is actually made of

The aggregate story in north Mississippi concrete

North Mississippi concrete, in the Tupelo and Oxford markets, runs on local chert gravel plus limestone hauled in from out of state. No one quarries commercial-grade limestone in the area. The local rock is Coastal Plain chert gravel and sand. It comes from the Tuscaloosa Gravels and from Pleistocene river terraces older than the loess, along the Mississippi-Alabama line from Tishomingo through Lowndes County. The closest limestone quarries sit 1 to 2 hours away, in Alabama or north-central Mississippi.

Our Mississippi concrete flooring hub lists the north Mississippi cities we serve.

Where does north Mississippi aggregate actually come from?

Crushed limestone comes in by truck or rail. Most of it is from north Alabama, out of the Fort Payne Formation at quarries like Vulcan Materials’ Fort Payne Quarry, and some comes from central Tennessee. Distance costs money. That haul shows up in the concrete price, unlike in states with hard rock close by.

The cement comes from outside too, from plants in Alabama, Tennessee, or Missouri. Lowndes County had its own cement plant, Holcim’s Artesia plant, until Holcim mothballed it in 2009 and quit making cement there for good in 2011. Amrize has owned the site since Holcim spun it off in 2025.

Rogers Group’s yard at the Port of Columbus, in Lowndes County, takes in crushed limestone by barge. None of it comes out of the ground there. Foley Materials’ Columbus Quarry sells sand, gravel, and railroad ballast across the Southeast. And APAC Mississippi runs an MDOT-approved gravel pit at Tremont.

How does the imported-aggregate mix affect polished floors?

A polished floor here reads light gray to warm beige cream, with scattered tan and rust flecks of chert. Source matters. A mix heavy on Alabama or Tennessee limestone polishes to a cleaner, more even pale gray. One heavy on Tuscaloosa chert gravel shows more color change and a warmer tone.

The coarse rock travels far and comes from several competing sources, not one quarry face. So mixes here change more from pour to pour than where hard rock is close. If you want a polished concrete finish to match across slabs poured on different days, the spec should name one source pit before the first pour. Chert-heavy gravel polishes with an earth-tone speckle. Deeply weathered chert can cause pop-outs, small chips that break loose from the surface, so polished work should call for dense, washed chert. Tuscaloosa chert can also react with the cement and crack the slab from inside. That’s called alkali-silica reaction (ASR). The answer is ASTM C1260/C1567 testing on the local chert, at least 20 percent Class F fly ash or at least 25 percent slag, and low-alkali cement (Na2Oeq at or under 0.60 percent). Stain comes out mottled and natural-looking instead of even, much like it does on Memphis concrete. Plan for that. Broom finishes are simple, and local crews know them well.

What Does Concrete Work in Olive Branch Look Like?

Polished concrete floor in luxury home entryway reflecting chandelier and modern interior designAction Powersports custom logo embedded in glossy black epoxy showroom floorRound Barn polished concrete floor with mirror-like reflections of windows in dark high-gloss finishPolished charcoal concrete floors in open-plan luxury home with stone fireplace and floating staircasePolished dark concrete floor in restaurant bar area with branded bar stools, tap handles and TVsMetallic epoxy floor in dark amber and brown marble swirl pattern with mirror-like gloss finishMetallic epoxy floor with colorful light-ray inlays at Brady Theatre in performing arts venueExpansive sealed concrete floor in double-height residential great room with French doors and transom windowsLow-angle dramatic view of polished concrete floor in large warehouse with column reflectionsQuarter-sawn wood-plank concrete overlay detail showing realistic grain texture and warm tonesHigh-gloss sealed outdoor concrete slab with mirror-like reflection of a boat trailer in daytimePolished concrete floor in Westmoore Community Church lobby viewed from wider angle

How far will Bel Covo travel to pour concrete in Olive Branch?

Bel Covo serves Olive Branch concrete projects within the standard service radius, and our crews are typically 3-6 weeks booked at any given moment. Every quote is itemized to show the cost of each step of the work, including the mobilization that gets equipment on site, so the quote doubles as the order of operations for your project. On accepted work, billing follows those same steps and shows the completion percentage of each as it happens, with nothing buried in a vague lump sum. Call 901-589-3528 for a straight answer in under two minutes.

Which concrete services does Bel Covo offer in Olive Branch?

Our Olive Branch crews handle polished concrete, epoxy and polyaspartic coatings, decorative staining, driveways, patios, and repair work. Every job follows the same Pour-4-Polish process and finish discipline used on our flagship projects. The related links below point to the specific service pages that match common Olive Branch requests.

What questions come up most about Olive Branch concrete?

Do you take concrete projects in Olive Branch, Mississippi?

Yes. Olive Branch is inside our Memphis coverage, about 19 miles southeast of Memphis in eastern DeSoto County. We take warehouse, commercial, and home jobs along the Goodman Road corridor and in the distribution parks near the Memphis airport. Crews dispatch from our Memphis team. Travel shows up as its own line on every quote, so you see it before you commit.

Do you handle warehouse and distribution floors in Olive Branch?

Yes. The distribution parks here sit close to the Memphis air-cargo hub, and their floors take forklifts, pallet jacks, and rolling loads all day. Ordinary slab coatings fail under that inside a year. For heavy traffic we polish the slab with a hardener. Where chemicals spill, we use 100 percent solids epoxy with a broadcast aggregate. Either way, the joints and steel match the rack loads.

How much does a warehouse floor cost in Olive Branch?

Polished concrete with a hardener runs $3.83 to $6.25 a square foot. A 100 percent solids epoxy with a broadcast aggregate runs $6.08 to $10.17, depending on the chemicals and the joint work. A slab that only needs cleaning, hardening, and a sealer runs $1.31 to $3.42. Slab condition and a site walk set the final number, and the quote tool gives you a starting one.

Can you coat a residential garage in an Olive Branch subdivision?

Yes. We grind the slab so the coating can bite in, then prime it with a 100 percent solids epoxy. Colored flake goes into the next coat until the floor won't take any more, and clear coats lock it in. That epoxy build is best indoors. For a garage that takes sun and hot tires, we steer you to the polyaspartic build.

What concrete services does Bel Covo offer in Olive Branch?

Warehouse and distribution floors, polished concrete, epoxy and polyaspartic garage floors, decorative concrete, driveways, patios, and new slabs. A new slab that will be polished or coated goes through our Pour-4-Polish process. Olive Branch leans toward distribution work, with plenty of home jobs beside it. The quote calculator prices each service from your square footage, slab condition, and use.

Last updated:

Ready to transform your floor?

Get a free, no-obligation quote for your project.

DeSoto County, Mississippi

See concrete work across DeSoto County, Mississippi →