Skip to main content
Bel Covo
modern sleek onyx polished concrete

Concrete contractor in Southaven, MS

What does concrete flooring cost in Southaven, Mississippi?

Concrete flooring in Southaven runs the same ranges as the broader Mississippi market: polished concrete lands in the low-to-mid single digits per square foot, stained and decorative systems fall in the middle, and high-end epoxy or metallic builds reach the top of the range. Slab condition, square footage, and finish selection all move the real number. The regional breakdown below walks through what actually drives a Southaven quote up or down.

Two kinds of concrete work in Southaven

We’re a concrete contractor in Southaven, MS, and our Memphis team handles the work here. Southaven is a city of about 52,000, just south of Memphis at the Tennessee line. The concrete work comes in two kinds: garage floors in the subdivisions, and polished floors in Goodman Road shops and restaurants. Polished concrete runs $3.83 to $6.25 a square foot with us. Get your price now.

Why does Southaven carry so much commercial floor work?

Southaven is where DeSoto County shops and eats out. People drive in from all over North Mississippi and the Memphis metro to the stores and restaurants on Goodman Road. So there’s more commercial floor work here than in the suburbs to the east, which are mostly homes.

Polished concrete does most of that work. We polish a store floor with a lithium hardener. It reacts with the free lime in the slab and locks the surface, so carts have no topcoat to peel. A commercial kitchen needs urethane cement or a 100 percent solids epoxy that takes grease, heat, and washdown. We joint and reinforce each slab for the loads the tenant really brings. See polished concrete details.

Loess ground and Senatobia gravel under a Southaven slab

The rock in the mix stays about the same from job to job. Ready-mix for DeSoto County draws sand and gravel from plants like Memphis Stone & Gravel - Senatobia Plant, just south in Tate County. The ground under the slab is what changes. DeSoto County sits on the loess bluffs and terraces above the flat Mississippi River bottom. Loess is a fine silt the wind laid down. It packs well, but it pumps and settles under a slab if the base is thin or the packing is rushed.

A store slab also carries more than a home garage. So on a store or restaurant floor, we pack the ground to 95 percent Proctor density, the standard test for how tight soil is packed. Then we lay a graded rock base and size the steel for the rolling and rack loads. The ACI 302.1R guide sets the joint spacing and how flat the finish must be. We write the spec down, so the tenant has a record of what’s under the floor.

Which floor specs fit Southaven work?

  • A store sales floor on Goodman Road: polished concrete with a hardener.
  • A restaurant kitchen or back room: urethane cement or 100 percent solids epoxy, with no recoat cycle to stop the kitchen.
  • A garage in the subdivisions: RESA Flake, our epoxy flake floor coating, or the polyaspartic build for a fast cure.
  • A living room or other inside space: polished concrete or decorative concrete.
  • A new driveway: our standard concrete driveway quote is a 5 inch slab on a packed gravel base, with rebar, poured with a 4500 PSI mix. A 4,000 PSI mix is the least you should accept on any bid, but it’s not what we pour.
  • A new interior slab: we pour it through Pour-4-Polish, so the pour spec is written for the floor that goes on it.
  • A patio: a concrete patio with the finish you pick.

What should Southaven owners know about DeSoto County concrete?

Southaven is hot and humid. Summer dew points sit in the low 70s, and about 53 inches of rain falls a year. That damp pushes water vapor up through a slab. Lay an epoxy film over a slab giving off too much vapor, and it blisters and peels inside a season.

We check every slab. When its age or an old floor covering raises a flag, we test it before we pick a system. That’s a calcium chloride test per ASTM F1869, or a humidity probe set into the slab per ASTM F2170. Outdoor slabs still see a handful of freeze-thaw cycles each winter. So we seal them with a penetrating siloxane that soaks in, instead of a film that traps vapor.

Check for moisture before a store floor goes down

A bid for a polished or coated store floor that never checks for moisture puts your opening date at risk. When the check calls for a test, it runs 24 to 72 hours. That costs less than redoing a failed floor in month four.

How does Southaven pricing come together on the quote?

Size, prep, and the system set the price. A 2,500-square-foot store floor with a Level 2 to Level 3 polish runs $9,450 to $15,450 before any drive cost. Our standard flake garage floor runs $8.55 to $10.39 a square foot. That’s the epoxy build; the polyaspartic build is priced on your quote. We price urethane cement kitchen floors per job, after we see the kitchen, because the prep and the build are heavier.

Southaven sits well inside the first 40 road miles from our Memphis team, so the quote tool charges no mileage. It figures the rest from your address and how long the job runs, and you see each line before you say yes.

See what your Southaven floor costs online

Enter your square footage and your Southaven address. The quote tool returns an estimate with materials, labor, and any travel spelled out.

Which DeSoto County cities does Bel Covo cover near Southaven?

We cover several DeSoto County towns, all within 25 miles of the Memphis core. Our Memphis team also works in Horn Lake just west, Olive Branch about 12 miles east, Hernando to the south on I-55, and Coldwater farther down the road, plus nearby addresses in Tate and Marshall counties. See our Mississippi state hub and the national locations index.

What the concrete in Mississippi is actually made of

The aggregate story in north Mississippi concrete

North Mississippi concrete, in the Tupelo and Oxford markets, runs on local chert gravel plus limestone hauled in from out of state. No one quarries commercial-grade limestone in the area. The local rock is Coastal Plain chert gravel and sand. It comes from the Tuscaloosa Gravels and from Pleistocene river terraces older than the loess, along the Mississippi-Alabama line from Tishomingo through Lowndes County. The closest limestone quarries sit 1 to 2 hours away, in Alabama or north-central Mississippi.

Our Mississippi concrete flooring hub lists the north Mississippi cities we serve.

Where does north Mississippi aggregate actually come from?

Crushed limestone comes in by truck or rail. Most of it is from north Alabama, out of the Fort Payne Formation at quarries like Vulcan Materials’ Fort Payne Quarry, and some comes from central Tennessee. Distance costs money. That haul shows up in the concrete price, unlike in states with hard rock close by.

The cement comes from outside too, from plants in Alabama, Tennessee, or Missouri. Lowndes County had its own cement plant, Holcim’s Artesia plant, until Holcim mothballed it in 2009 and quit making cement there for good in 2011. Amrize has owned the site since Holcim spun it off in 2025.

Rogers Group’s yard at the Port of Columbus, in Lowndes County, takes in crushed limestone by barge. None of it comes out of the ground there. Foley Materials’ Columbus Quarry sells sand, gravel, and railroad ballast across the Southeast. And APAC Mississippi runs an MDOT-approved gravel pit at Tremont.

How does the imported-aggregate mix affect polished floors?

A polished floor here reads light gray to warm beige cream, with scattered tan and rust flecks of chert. Source matters. A mix heavy on Alabama or Tennessee limestone polishes to a cleaner, more even pale gray. One heavy on Tuscaloosa chert gravel shows more color change and a warmer tone.

The coarse rock travels far and comes from several competing sources, not one quarry face. So mixes here change more from pour to pour than where hard rock is close. If you want a polished concrete finish to match across slabs poured on different days, the spec should name one source pit before the first pour. Chert-heavy gravel polishes with an earth-tone speckle. Deeply weathered chert can cause pop-outs, small chips that break loose from the surface, so polished work should call for dense, washed chert. Tuscaloosa chert can also react with the cement and crack the slab from inside. That’s called alkali-silica reaction (ASR). The answer is ASTM C1260/C1567 testing on the local chert, at least 20 percent Class F fly ash or at least 25 percent slag, and low-alkali cement (Na2Oeq at or under 0.60 percent). Stain comes out mottled and natural-looking instead of even, much like it does on Memphis concrete. Plan for that. Broom finishes are simple, and local crews know them well.

What Does Concrete Work in Southaven Look Like?

Polished concrete floor in luxury home entryway reflecting chandelier and modern interior designAction Powersports custom logo embedded in glossy black epoxy showroom floorRound Barn polished concrete floor with mirror-like reflections of windows in dark high-gloss finishPolished charcoal concrete floors in open-plan luxury home with stone fireplace and floating staircasePolished dark concrete floor in restaurant bar area with branded bar stools, tap handles and TVsMetallic epoxy floor in dark amber and brown marble swirl pattern with mirror-like gloss finishMetallic epoxy floor with colorful light-ray inlays at Brady Theatre in performing arts venueExpansive sealed concrete floor in double-height residential great room with French doors and transom windowsLow-angle dramatic view of polished concrete floor in large warehouse with column reflectionsQuarter-sawn wood-plank concrete overlay detail showing realistic grain texture and warm tonesHigh-gloss sealed outdoor concrete slab with mirror-like reflection of a boat trailer in daytimePolished concrete floor in Westmoore Community Church lobby viewed from wider angle

How far will Bel Covo travel to pour concrete in Southaven?

Bel Covo serves Southaven concrete projects within the standard service radius, and our crews are typically 3-6 weeks booked at any given moment. Every quote is itemized to show the cost of each step of the work, including the mobilization that gets equipment on site, so the quote doubles as the order of operations for your project. On accepted work, billing follows those same steps and shows the completion percentage of each as it happens, with nothing buried in a vague lump sum. Call 901-589-3528 for a straight answer in under two minutes.

Which concrete services does Bel Covo offer in Southaven?

Our Southaven crews handle polished concrete, epoxy and polyaspartic coatings, decorative staining, driveways, patios, and repair work. Every job follows the same Pour-4-Polish process and finish discipline used on our flagship projects. The related links below point to the specific service pages that match common Southaven requests.

What questions come up most about Southaven concrete?

Do you take concrete projects in Southaven, Mississippi?

Yes. Southaven is in DeSoto County, just across the state line from Memphis along I-55 and Goodman Road. Our Memphis team handles home, commercial, and retail concrete here, and Southaven sits well inside our Memphis metro coverage area. Every quote spells out any travel cost, so you see it before you agree to anything.

Do you handle commercial floors along the Goodman Road retail corridor?

Yes. The stores, restaurants, and entertainment spots going in along Goodman Road bring steady commercial polish and coating work. For store sales floors, we spec polished concrete with a surface hardener. For commercial kitchens and back rooms, we spec urethane cement or 100 percent solids epoxy. And we joint and reinforce each slab for the real rolling and point loads the tenant brings.

How much does polished concrete cost in Southaven?

Polished concrete in Southaven generally runs $3.83 to $6.25 a square foot. The sheen level, the size of the floor, and the shape the slab is in set where you land in that range. A home basement or garage polish sits in a similar range, depending on prep. The online quote tool builds a number for your address in about 2 minutes.

Can you coat a residential garage in a Southaven subdivision?

Yes. Our standard flake floor is RESA Flake, an epoxy build. We grind the slab rough (CSP 3 or more) and prime it. Flakes go into an 18 to 22 mil coat until it takes no more, then 16 to 18 mils of clear epoxy and a 4 mil urethane top lock them in. Want a faster cure and a floor that shrugs off hot tires from the summer commute? Our premium build uses polyaspartic, and we price it on your quote.

What concrete services does Bel Covo offer in Southaven?

Polished concrete, epoxy and polyaspartic garage floors, decorative and stained concrete, commercial floor systems, driveways, patios, and new slab pours through our Pour-4-Polish process. In Southaven, the work splits between home floors in the subdivisions and commercial polish along Goodman Road. The quote calculator prices each service from your square footage, slab condition, and address.

Last updated:

Ready to transform your floor?

Get a free, no-obligation quote for your project.

DeSoto County, Mississippi

See concrete work across DeSoto County, Mississippi →