Skip to main content
Bel Covo
modern sleek onyx polished concrete

Concrete contractor in Cleveland, TN

What does concrete flooring cost in Cleveland, Tennessee?

Concrete flooring in Cleveland runs the same ranges as the broader Tennessee market: polished concrete lands in the low-to-mid single digits per square foot, stained and decorative systems fall in the middle, and high-end epoxy or metallic builds reach the top of the range. Slab condition, square footage, and finish selection all move the real number. The regional breakdown below walks through what actually drives a Cleveland quote up or down.

What drives concrete floor demand in Cleveland, Tennessee?

Cleveland is the county seat of Bradley County, a town of about 47,000 with plants that make food, batteries, and home appliances. As a concrete contractor in Cleveland, TN, we handle both sides of that town. Plant floors get urethane cement and high-build coatings. Homeowners get driveways, shop slabs, and barndominium pads. Get your price now.

US-64, also called Corridor K, runs through downtown and east toward Ocoee. The freight and trade traffic on that road tilts Cleveland’s work more commercial than most of its Bradley County neighbors.

Bradley County subgrade note

Most Cleveland driveways and shop slabs sit on Valley and Ridge clay-silt. It swells when it's wet and shrinks in dry spells. So we compact the base to spec and lay out the joints with more care than we would on stable sandy ground. Both go into our Bradley County pour spec before any coating or polish goes on.

What does stone from the quarries near Cleveland mean for your slab?

Most of the crushed stone in Bradley County concrete comes from Vulcan Materials and Martin Marietta quarries in Hamilton County, just to the west. Both dig into the rock that runs under this part of East Tennessee: Knox Group dolomite and Chickamauga limestone. Ground and honed, that limestone polishes to a warm, mixed gray with a cool tint and a few buff flecks of dolomite. On polished floors in Cleveland’s public buildings and restaurants, we work with that color instead of fighting it. Our standard polish reads even and clean on the local stone.

The weather here swings hard. A west-facing garage floor can sit in the upper 20s during a January cold snap and pass 100 degrees by mid-August. So on an outdoor Cleveland slab, air entrainment (tiny air bubbles in the mix) and well-spaced control joints aren’t optional.

How do concrete coatings and new slabs price out in Cleveland?

Garage coatings in Cleveland run $8.55 to $10.39 a square foot for our full flake floor on a slab in fair shape. We call it RESA Flake. RESA is our name for flake, quartz, or metallic set in resin. The priced build is epoxy: vinyl flake broadcast into an 18 to 22 mil coat, locked in by 16 to 18 mils of clear epoxy and a 4 mil urethane top. Polyaspartic is our premium build, priced on your quote. A quartz or metallic floor (RESA Quartz or RESA Metallic) runs $6.08 to $10.17 a square foot. Our Chattanooga team covers epoxy flooring out US-64 in Ocoee, too, at the same rates plus the drive.

For new slab construction, a shop or barndo slab with #4 rebar on 18-inch centers starts at $7.04 a square foot. If you want it 6 inches thick, the quote tool prices that thickness. Driveways run $6.96 to $16.43 a square foot, from a plain broom finish up to decorative.

Polished concrete for a store, restaurant, or plant floor runs $3.83 to $6.25 a square foot. The low end is our standard polish. Grout, a second densifier coat, and other options move it up.

See what your Cleveland floor costs

Enter your square footage and the kind of project, and you'll get a detailed price.

What floor specs do Bradley County plants and homes need?

Plant floors set the bar in Cleveland. Food, battery, and appliance plants put heat and chemicals on the floor every shift. Those floors get urethane cement, a cement and urethane blend that holds up to heat and chemicals, or a high-build epoxy rated for heat shock. We price that work per job, after we see the floor and the plant’s spec.

Our Pour-4-Polish process takes new construction from the pour to the finished floor in one scope. We write the pour spec for the floor that goes on it. That matters when a production schedule can’t stop for several rounds of concrete work.

Homes and farms in Bradley County mostly need driveways, front patios, and barndominium pads. Plenty of lots sit on a hillside in this Valley and Ridge country. A slope adds footing work and makes it harder to get trucks in. We price that access into the quote up front, so it never shows up later as a surprise.

Older slabs in Cleveland’s historic commercial core are often of unknown age. We check every slab. When its history or a stain flags a moisture risk, we test it before we pick a coating. A sealer or epoxy over a slab that’s giving off too much moisture blisters early, no matter how well we grind it.

Garage floor coatings and polished concrete in Bradley County come from the same Chattanooga team. So do residential concrete and commercial flatwork.

Other Tennessee cities near Cleveland

Bradley County sits just east of Chattanooga. Our Chattanooga team also covers Athens, Soddy-Daisy, and the rest of our Tennessee service area.

What the concrete in Tennessee is actually made of

The aggregate story in West Tennessee concrete

Memphis and West Tennessee concrete uses Mississippi River chert gravel and sand from local pits. Crushed limestone comes in by rail or barge from Middle Tennessee (the Fort Payne Formation and the Mississippian limestone above it). West Tennessee has no hard-rock limestone quarry. Its bedrock sits under hundreds of feet of loose Coastal Plain sediment, so any coarse limestone in a Memphis slab has come 150 miles or more. Our Tennessee concrete flooring page covers where we work.

What gives Memphis polished floors their multi-toned cream look?

The river gravel is old Devonian and Mississippian chert, worn round over hundreds of miles of river. So the pebbles run gray, brown, red, cream, and black. No crushed-limestone area has that range. A polished floor reads as a warm cream to buff, peppered with tan, honey, gray, and reddish-brown pebbles. Ground and honed, it looks speckled, not one clean color. Darker gravel mixes lean toward a light khaki. A mix made with shipped-in limestone polishes closer to an even pale gray, the quieter choice.

Weathered chert can be porous, and it can react with cement and crack a slab from inside (alkali-silica reaction). Good producers screen for it. The loess bluffs (wind-blown silt) east of the river add silty sand to local mixes. That can raise how much water a hot-weather pour needs.

Local producers and cement

Memphis Stone and Gravel, part of Granite Construction, is the biggest local producer. It runs 3 sand and gravel mines in Mississippi River deposits and is building a fourth. Cement comes down the river by barge from Cape Girardeau and Festus, Missouri, to the Buzzi Unicem USA terminal at the Port of Memphis. No cement kiln runs in West Tennessee.

Does the river aggregate create problems for stain or coating finishes?

For stain, yes. Chert pebbles take acid stain poorly while the cement around them takes it well, so stained floors here come out mottled. A broom finish hides the gravel, though round gravel makes a tight cream harder to bring up. Polish shows the chert loud and clear. That’s character in a home or a small shop. On a big commercial floor meant to look even gray, it’s busy.

So pick by the look you want:

  • Speckled and many-toned: polish a river-gravel slab.
  • Even pale gray: ask for a limestone mix before the pour. An old slab keeps the look it has.
  • One even color on an existing slab: an epoxy coating over the ground slab covers the gravel.

What about Nashville, Knoxville, and Chattanooga?

Middle and East Tennessee have crushed stone quarries close to town: Rogers Group’s Whites Creek quarry in Nashville, Vulcan Materials’ Dixie Lee quarry in Farragut near Knoxville, and Martin Marietta and Vulcan quarries in Chattanooga. Our Nashville, Knoxville, and Chattanooga teams work that side of the state. A mix made with that crushed limestone polishes closer to an even pale gray than the river-gravel floors above.

What Does Concrete Work in Cleveland Look Like?

Ground-level close-up of completed white vinyl chip epoxy floor showing chip texture and depth with service counter visible in distanceCompleted white vinyl chip epoxy floor in Ladd's showroom with worker in background and Club Car branding bannersCompleted white vinyl chip epoxy floor at Ladd's showroom looking toward service counter and green accent wallReflective brown polished concrete floor with fully exposed stone aggregate.Glossy brown polished concrete floor with exposed aggregate beside built in cabinets.full exposure polished concrete floor in a residential great room by Bel CovoPolished concrete floor in luxury home entryway reflecting chandelier and modern interior designAction Powersports custom logo embedded in glossy black epoxy showroom floorRound Barn polished concrete floor with mirror-like reflections of windows in dark high-gloss finishPolished charcoal concrete floors in open-plan luxury home with stone fireplace and floating staircasePolished dark concrete floor in restaurant bar area with branded bar stools, tap handles and TVsMetallic epoxy floor in dark amber and brown marble swirl pattern with mirror-like gloss finish

How far will Bel Covo travel to pour concrete in Cleveland?

Bel Covo serves Cleveland concrete projects within the standard service radius, and our crews are typically 3-6 weeks booked at any given moment. Every quote is itemized to show the cost of each step of the work, including the mobilization that gets equipment on site, so the quote doubles as the order of operations for your project. On accepted work, billing follows those same steps and shows the completion percentage of each as it happens, with nothing buried in a vague lump sum. Call 423-373-7762 for a straight answer in under two minutes.

Which concrete services does Bel Covo offer in Cleveland?

Our Cleveland crews handle polished concrete, epoxy and polyaspartic coatings, decorative staining, driveways, patios, and repair work. Every job follows the same Pour-4-Polish process and finish discipline used on our flagship projects. The related links below point to the specific service pages that match common Cleveland requests.

What questions come up most about Cleveland concrete?

Do you take concrete projects in Cleveland, Tennessee?

Yes. Cleveland is inside our Chattanooga coverage, about 33 miles east of Chattanooga along US-64. We pour driveways and shop and barndo slabs, and we coat garages and polish concrete across Bradley County. Crews come from our Chattanooga team. The drive is its own line on every quote, so you see it before you commit.

What does a concrete driveway cost in Cleveland?

Cleveland driveways run $6.96 to $16.43 a square foot, set by thickness, steel, and finish. A two-car driveway of about 500 square feet runs $3,650 to $8,650 before the drive cost (our trip to your site). A small driveway runs above the per-foot range, since setup spreads over fewer feet. The quote tool prices yours in 2 minutes.

Can you pour and coat a garage floor in the same scope?

Yes. Our Pour-4-Polish process puts the pour, the cure time, and the coating in one scope. We write the pour spec for the floor that goes on it. You get one warranty for our workmanship on the finished floor. On Bradley County clay-silt, we check the compaction before the pour, not after.

What types of floors do you install in Bradley County?

Driveways, patios, shop and barndo slabs, garage epoxy and polyaspartic coatings, and polished concrete. Plants and commercial tenants along US-64 (Corridor K) add flatwork, equipment pads, and urethane cement where the floor takes heat and chemicals.

Last updated:

Ready to transform your floor?

Get a free, no-obligation quote for your project.