Skip to main content
Bel Covo
modern sleek onyx polished concrete

Concrete contractor in Collierville, TN

What does concrete flooring cost in Collierville, Tennessee?

Concrete flooring in Collierville runs the same ranges as the broader Tennessee market: polished concrete lands in the low-to-mid single digits per square foot, stained and decorative systems fall in the middle, and high-end epoxy or metallic builds reach the top of the range. Slab condition, square footage, and finish selection all move the real number. The regional breakdown below walks through what actually drives a Collierville quote up or down.

What sets Collierville apart from the rest of the Memphis metro?

Collierville sits on the east edge of Shelby County and has about 51,000 people. Homes here run from old houses near the town square to custom builds on five-acre horse farms. As a concrete contractor in Collierville, TN, we polish great rooms, coat three- and four-car garages, and pour barn and barndominium slabs. Get your price now.

How does a trip to Collierville work?

Collierville is inside our Memphis team’s coverage, about 30 miles southeast of downtown Memphis along the Bill Morris Parkway. For our crews, that’s roughly a 40-minute drive. On a floor of 1,000 square feet or more, the trip barely moves your price per foot. We often book Collierville work the same week as jobs in Germantown, Eads, and along Houston Levee Road.

Same-week block scheduling across Shelby County

If your Collierville date can move a little, tell us when you ask for a price. We usually put Collierville, Germantown, and Eads jobs on one trip, which keeps the travel line low on each one.

Which three floor specs define Collierville demand?

Polished concrete in custom homes and renovation builds

Custom homes in Collierville often put polished concrete in great rooms, kitchens, and walkout basements. Those rooms get lots of sun, and many have radiant heat. A concrete floor soaks up heat from south-facing glass during the day and gives it back slowly after dark. That’s just what a radiant system wants from a floor.

We grind in steps with diamond tools. Our standard first cut is two passes at 30 grit, and most floors show a salt-and-pepper look from it. Finer grits, up to 800 or 1500, then set the shine you picked. The cut-depth guide shows each look side by side.

Nothing sits on top of the slab. So there’s no topcoat to peel and no haze to fight after a humid Mid-South summer. Vapor from the ground passes right through, with no film to push against. Upkeep is a damp mop with plain water, not a strip-and-wax cycle. Our Chinquapin House polish in Collierville is one of these home floors, and its photos are on this page. See polished concrete details.

Epoxy and polyaspartic floors for multi-car and carriage-house garages

Collierville garages aren’t the usual two-car bay. A lot of custom homes here have three- and four-car garages, or a detached carriage house with finished rooms upstairs. That floor has to handle hot tires after a summer drive, spills from weekend mechanics, and big temperature swings in a garage that’s only partly heated and cooled.

Our RESA Flake floor, a resinous floor coating (RESA is our name for a resin floor with flake or sand locked inside), starts with an 18 to 22 mil flake coat. Then come 16 to 18 mils of clear epoxy and a 4 mil urethane topcoat. Polyaspartic is the premium build. It cures fast and shrugs off hot tires, so it’s our garage pick, and it’s priced on your quote. Either way, we grind the slab rough, to CSP 3 (the scale bids use for how rough a ground slab is), so the coating bites in. Learn about epoxy and polyaspartic garage floors.

Equestrian slabs, barndominiums, and carriage houses

East Collierville and the Eads area have a lot of horse property. The barndominium has also moved from rural Tennessee into the acreage market here. Barn aisles, wash racks, tack rooms, and run-in shed slabs each need a different finish. A wash rack needs slope, a drain, and a broom finish that won’t get slick. A tack room does best with a sealed utility floor that holds up to strong cleaners. A carriage-house living space can take a polished floor with the stone showing, so it reads as a room and not a barn. Through our Pour-4-Polish process, one written spec covers the slab and the floor that goes on it, from packing the dirt to the last buff. Explore barndominium shop slabs.

Damp Mid-South air under a garage coating

The Memphis area gets about 53 inches of rain a year, and summer humidity stays above 70%. So water vapor is always pushing up through a bare slab. Put a coating over a slab giving off too much of it, and within 18 to 36 months the coating bubbles, peels, or lets go at the bond.

We check the slab on every Collierville coating job. When it shows one of these warning signs, we test it:

  • a pour from before 1990
  • a low lot near the Wolf River, where the ground stays wet
  • a coating that already failed on the same slab

The ASTM F1869 test measures how many pounds of vapor 1,000 square feet of slab gives off in 24 hours. We write the readings into your job file. Over 3 pounds, we put down a moisture barrier primer before the coating, or we switch the room to a polished floor. On a flagged slab, that one test heads off the 18-month bond failure behind most coating callbacks in the Mid-South.

What should Collierville owners know about local rock and subgrade?

On a new slab, the dirt under it is where things go right or wrong. Skip that prep, and the slab cracks within a few seasons, no matter how good the mix is. We pack the ground to 95% Proctor density (the standard test for how tightly soil is packed) and lay a well-graded rock base before the first truck shows up. The cement comes through terminals like the Buzzi Unicem USA Memphis Terminal - Riverside Station, about 23 miles west in Memphis, so the haul to a Collierville site is short. The American Concrete Institute (ACI) sets fiber or rebar and joint spacing by slab thickness. We follow it and write it down, so you have a record of what’s under your floor.

Freeze-thaw on outside slabs

Collierville sees about 40 to 50 freeze-thaw cycles a year, depending on the winter. Water trapped in bare concrete grows about 9% when it freezes, and that breaks the cement apart from the inside. It’s the flaking (surface scaling) you see on old Mid-South driveways that were finished without a good cure or sealer. We pour exterior concrete flatwork at 4,000 PSI or stronger. We cure it with a curing compound picked for the weather on pour day. Then we seal outside slabs with a penetrating siloxane, which soaks in instead of forming a film that traps vapor.

What does the quote calculator include for Collierville pricing?

Polished concrete runs $3.83 to $6.25 a square foot in the Memphis area, set by size, prep, and the options you add. A flake garage floor runs $8.55 to $10.39 a square foot for our standard epoxy flake build. Polyaspartic is priced on your quote. A barndominium or shop slab prices from its thickness, steel, and finish, not a flat per-foot rate. No phone tag.

See what your Collierville floor costs online

Enter your square footage and project address. The calculator gives you a detailed estimate with materials, labor, and travel included.

Which Shelby County and West Tennessee cities does Bel Covo cover?

Our Memphis team also covers Memphis, Bartlett on the northeast side of the metro, Jackson along I-40 to the east, and Dyersburg up US-51 to the north. So do Germantown, Eads, Arlington, and the rest of eastern Shelby County. The Tennessee state hub and the national locations index show the full map.

What the concrete in Tennessee is actually made of

The aggregate story in West Tennessee concrete

Memphis and West Tennessee concrete uses Mississippi River chert gravel and sand from local pits. Crushed limestone comes in by rail or barge from Middle Tennessee (the Fort Payne Formation and the Mississippian limestone above it). West Tennessee has no hard-rock limestone quarry. Its bedrock sits under hundreds of feet of loose Coastal Plain sediment, so any coarse limestone in a Memphis slab has come 150 miles or more. Our Tennessee concrete flooring page covers where we work.

What gives Memphis polished floors their multi-toned cream look?

The river gravel is old Devonian and Mississippian chert, worn round over hundreds of miles of river. So the pebbles run gray, brown, red, cream, and black. No crushed-limestone area has that range. A polished floor reads as a warm cream to buff, peppered with tan, honey, gray, and reddish-brown pebbles. Ground and honed, it looks speckled, not one clean color. Darker gravel mixes lean toward a light khaki. A mix made with shipped-in limestone polishes closer to an even pale gray, the quieter choice.

Weathered chert can be porous, and it can react with cement and crack a slab from inside (alkali-silica reaction). Good producers screen for it. The loess bluffs (wind-blown silt) east of the river add silty sand to local mixes. That can raise how much water a hot-weather pour needs.

Local producers and cement

Memphis Stone and Gravel, part of Granite Construction, is the biggest local producer. It runs 3 sand and gravel mines in Mississippi River deposits and is building a fourth. Cement comes down the river by barge from Cape Girardeau and Festus, Missouri, to the Buzzi Unicem USA terminal at the Port of Memphis. No cement kiln runs in West Tennessee.

Does the river aggregate create problems for stain or coating finishes?

For stain, yes. Chert pebbles take acid stain poorly while the cement around them takes it well, so stained floors here come out mottled. A broom finish hides the gravel, though round gravel makes a tight cream harder to bring up. Polish shows the chert loud and clear. That’s character in a home or a small shop. On a big commercial floor meant to look even gray, it’s busy.

So pick by the look you want:

  • Speckled and many-toned: polish a river-gravel slab.
  • Even pale gray: ask for a limestone mix before the pour. An old slab keeps the look it has.
  • One even color on an existing slab: an epoxy coating over the ground slab covers the gravel.

What about Nashville, Knoxville, and Chattanooga?

Middle and East Tennessee have crushed stone quarries close to town: Rogers Group’s Whites Creek quarry in Nashville, Vulcan Materials’ Dixie Lee quarry in Farragut near Knoxville, and Martin Marietta and Vulcan quarries in Chattanooga. Our Nashville, Knoxville, and Chattanooga teams work that side of the state. A mix made with that crushed limestone polishes closer to an even pale gray than the river-gravel floors above.

Chinquapin House Polish

Collierville, Tennessee

full exposure polished concrete floor in a residential great room by Bel Covo
Glossy brown polished concrete floor with exposed aggregate beside built in cabinets.
Glossy dark polished concrete floor with exposed aggregate in a residential kitchen.
Reflective brown polished concrete floor with fully exposed stone aggregate.

What Does Concrete Work in Collierville Look Like?

Ground-level close-up of completed white vinyl chip epoxy floor showing chip texture and depth with service counter visible in distanceCompleted white vinyl chip epoxy floor in Ladd's showroom with worker in background and Club Car branding bannersCompleted white vinyl chip epoxy floor at Ladd's showroom looking toward service counter and green accent wallPolished concrete floor in luxury home entryway reflecting chandelier and modern interior designAction Powersports custom logo embedded in glossy black epoxy showroom floorRound Barn polished concrete floor with mirror-like reflections of windows in dark high-gloss finishPolished charcoal concrete floors in open-plan luxury home with stone fireplace and floating staircasePolished dark concrete floor in restaurant bar area with branded bar stools, tap handles and TVsMetallic epoxy floor in dark amber and brown marble swirl pattern with mirror-like gloss finishMetallic epoxy floor with colorful light-ray inlays at Brady Theatre in performing arts venueExpansive sealed concrete floor in double-height residential great room with French doors and transom windowsLow-angle dramatic view of polished concrete floor in large warehouse with column reflections

How far will Bel Covo travel to pour concrete in Collierville?

Bel Covo serves Collierville concrete projects within the standard service radius, and our crews are typically 3-6 weeks booked at any given moment. Every quote is itemized to show the cost of each step of the work, including the mobilization that gets equipment on site, so the quote doubles as the order of operations for your project. On accepted work, billing follows those same steps and shows the completion percentage of each as it happens, with nothing buried in a vague lump sum. Call 901-589-3528 for a straight answer in under two minutes.

Which concrete services does Bel Covo offer in Collierville?

Our Collierville crews handle polished concrete, epoxy and polyaspartic coatings, decorative staining, driveways, patios, and repair work. Every job follows the same Pour-4-Polish process and finish discipline used on our flagship projects. The related links below point to the specific service pages that match common Collierville requests.

What questions come up most about Collierville concrete?

Do you take concrete projects in Collierville, Tennessee?

Yes. Collierville is inside our Memphis team's coverage, about 30 miles southeast of downtown Memphis along the Bill Morris Parkway. We take home, business, and horse-property concrete across Shelby County. Your quote lists travel as its own line, so you see it up front.

How much does polished concrete cost in Collierville?

Polished concrete in Collierville runs $3.83 to $6.25 a square foot. Size, slab condition, and how deep we cut move it. A 3,500-square-foot great room runs $13,000 to $21,300 plus our drive to your site, from a base polish up to every option. A big floor can land a bit under the per-foot range, since setup spreads over more feet.

Can Bel Covo coat the floors in a four-car or carriage-house garage?

Yes. Big garages and carriage houses are common in Collierville. We grind the slab rough so the coating grips, lay down an epoxy base coat, and throw color flake until it won't take any more. Our standard build locks the flake under clear epoxy and a urethane topcoat. Polyaspartic is the premium build, priced on your quote.

Do you pour and finish equestrian barn aisles and tack room slabs?

Yes. Collierville and Eads have a lot of horse property, and barn aisles, wash racks, and tack rooms are part of our Shelby County work. We pour reinforced slabs with the slope and drains the plan calls for. Then we finish each one for its use: a sealed utility floor, a broom finish, or polished with the stone showing.

Last updated:

Ready to transform your floor?

Get a free, no-obligation quote for your project.

Shelby County, Tennessee

See concrete work across Shelby County, Tennessee →