Skip to main content
Bel Covo
modern sleek onyx polished concrete

Concrete contractor in Farragut, TN

What does concrete flooring cost in Farragut, Tennessee?

Concrete flooring in Farragut runs the same ranges as the broader Tennessee market: polished concrete lands in the low-to-mid single digits per square foot, stained and decorative systems fall in the middle, and high-end epoxy or metallic builds reach the top of the range. Slab condition, square footage, and finish selection all move the real number. The regional breakdown below walks through what actually drives a Farragut quote up or down.

West Knox custom homes call for floors that match

Farragut is a West Knox town where about 87 percent of households own their homes. Builders compete on finish quality. We’re a concrete contractor in Farragut, TN, with a crew 18 miles east in Knoxville. Many lots here sit on hill slopes. Driveways, garages, polished interiors, and patios are part of what buyers expect.

What does Farragut’s building stock ask of a concrete contractor?

Custom and near-custom homes at this price point. Farragut’s residential fabric runs toward four-bedroom and larger homes with oversized garages, long driveways, and outdoor entertaining spaces. That means three concrete scopes show up repeatedly:

  • Garage floor coatings and polyaspartic systems on 2- and 3-car slabs, where owners want a surface tough enough for hot-tire pickup and road-salt drag, not a big-box DIY kit that peels inside 18 months. A full-chip broadcast flake system runs $8.55 to $10.39 per square foot; metallic and quartz finishes come in at $6.08 to $10.17.
  • Driveways on sloped or curved lots that reflect the custom footprint. A standard broom-finish 4-inch pour starts at $8.64 per square foot; a thicker reinforced slab with a decorative or salt-and-pepper finish costs more.
  • Polished and stained interiors for open-plan main floors and finished basements where the builder-grade alternative is 60-mil LVP over a moisture vapor problem. Polished concrete for a Farragut residential interior runs $3.83 to $6.25 per square foot based on sheen level and aggregate exposure.

Across this range of scopes, prep comes before product. We diamond-grind to CSP 3. We check a slab headed for a coating for signs of moisture. We probe the ground before we quote a driveway on a hillside lot. That is the spec, not a marketing distinction.

Hillside lots in Farragut can carry a footing adder

West Knox County's ridge-and-valley terrain means driveways and pads on sloped lots sometimes need additional excavation and forming work to establish grade. That work adds cost over a level-site pour. We assess the lot before we finalize the scope so the quote reflects the ground you actually have, not a flat-site assumption.

What stone does the Dixie Lee quarry feed into a Farragut slab?

Crushed limestone, the same carbonate aggregate that characterizes Valley and Ridge concrete across East Tennessee. Vulcan Materials - Dixie Lee Quarry operates in west Knox County, near Concord Road, supplying crushed limestone and dolomite to ready-mix plants serving this corridor. Farragut sits on the same Knox Group dolomite and Chickamauga limestone formation that underlies Knoxville to the east. That geology produces two effects on concrete work: a stable, well-draining subgrade on most lots, and an aggregate that polishes to a hard, bright, carbonate-flecked surface when exposed past 100 grit. A Farragut slab ground to aggregate exposure looks different from a Memphis slab (warm cream from Mississippi River chert) or a Middle Tennessee slab (cooler gray from Nashville Basin limestone); the Knox dolomite reads as a warm, variegated stone-fleck pattern that suits the custom-home aesthetic this market favors.

How does concrete work in Farragut schedule from the Knoxville team?

Farragut sits about 18 miles west of Knoxville, which puts it inside our Knoxville team’s regular rotation along I-40 and Kingston Pike. Work here books as a mobilization from our Knoxville team. Mobilization appears as a separate line on every quote before you commit, not bundled into the per-square-foot rate. Our crews are typically 3-6 weeks booked. The Pour-4-Polish specification puts the slab pour and the finish coating under one spec and one crew, which is how a new garage floor or an interior renovation goes from subgrade to finished surface without a contractor handoff. The rest of our East Tennessee coverage is on the Tennessee page.

See what your Farragut floor costs online

Enter your square footage and project details to get a project-specific estimate.

What the concrete in Tennessee is actually made of

The aggregate story in West Tennessee concrete

Memphis and West Tennessee concrete uses Mississippi River chert gravel and sand from local pits. Crushed limestone comes in by rail or barge from Middle Tennessee (the Fort Payne Formation and the Mississippian limestone above it). West Tennessee has no hard-rock limestone quarry. Its bedrock sits under hundreds of feet of loose Coastal Plain sediment, so any coarse limestone in a Memphis slab has come 150 miles or more. Our Tennessee concrete flooring page covers where we work.

What gives Memphis polished floors their multi-toned cream look?

The river gravel is old Devonian and Mississippian chert, worn round over hundreds of miles of river. So the pebbles run gray, brown, red, cream, and black. No crushed-limestone area has that range. A polished floor reads as a warm cream to buff, peppered with tan, honey, gray, and reddish-brown pebbles. Ground and honed, it looks speckled, not one clean color. Darker gravel mixes lean toward a light khaki. A mix made with shipped-in limestone polishes closer to an even pale gray, the quieter choice.

Weathered chert can be porous, and it can react with cement and crack a slab from inside (alkali-silica reaction). Good producers screen for it. The loess bluffs (wind-blown silt) east of the river add silty sand to local mixes. That can raise how much water a hot-weather pour needs.

Local producers and cement

Memphis Stone and Gravel, part of Granite Construction, is the biggest local producer. It runs 3 sand and gravel mines in Mississippi River deposits and is building a fourth. Cement comes down the river by barge from Cape Girardeau and Festus, Missouri, to the Buzzi Unicem USA terminal at the Port of Memphis. No cement kiln runs in West Tennessee.

Does the river aggregate create problems for stain or coating finishes?

For stain, yes. Chert pebbles take acid stain poorly while the cement around them takes it well, so stained floors here come out mottled. A broom finish hides the gravel, though round gravel makes a tight cream harder to bring up. Polish shows the chert loud and clear. That’s character in a home or a small shop. On a big commercial floor meant to look even gray, it’s busy.

So pick by the look you want:

  • Speckled and many-toned: polish a river-gravel slab.
  • Even pale gray: ask for a limestone mix before the pour. An old slab keeps the look it has.
  • One even color on an existing slab: an epoxy coating over the ground slab covers the gravel.

What about Nashville, Knoxville, and Chattanooga?

Middle and East Tennessee have crushed stone quarries close to town: Rogers Group’s Whites Creek quarry in Nashville, Vulcan Materials’ Dixie Lee quarry in Farragut near Knoxville, and Martin Marietta and Vulcan quarries in Chattanooga. Our Nashville, Knoxville, and Chattanooga teams work that side of the state. A mix made with that crushed limestone polishes closer to an even pale gray than the river-gravel floors above.

What Does Concrete Work in Farragut Look Like?

Ground-level close-up of completed white vinyl chip epoxy floor showing chip texture and depth with service counter visible in distanceCompleted white vinyl chip epoxy floor in Ladd's showroom with worker in background and Club Car branding bannersCompleted white vinyl chip epoxy floor at Ladd's showroom looking toward service counter and green accent wallReflective brown polished concrete floor with fully exposed stone aggregate.Glossy brown polished concrete floor with exposed aggregate beside built in cabinets.full exposure polished concrete floor in a residential great room by Bel CovoPolished concrete floor in luxury home entryway reflecting chandelier and modern interior designAction Powersports custom logo embedded in glossy black epoxy showroom floorRound Barn polished concrete floor with mirror-like reflections of windows in dark high-gloss finishPolished charcoal concrete floors in open-plan luxury home with stone fireplace and floating staircasePolished dark concrete floor in restaurant bar area with branded bar stools, tap handles and TVsMetallic epoxy floor in dark amber and brown marble swirl pattern with mirror-like gloss finish

How far will Bel Covo travel to pour concrete in Farragut?

Bel Covo serves Farragut concrete projects within the standard service radius, and our crews are typically 3-6 weeks booked at any given moment. Every quote is itemized to show the cost of each step of the work, including the mobilization that gets equipment on site, so the quote doubles as the order of operations for your project. On accepted work, billing follows those same steps and shows the completion percentage of each as it happens, with nothing buried in a vague lump sum. Call 865-484-3528 for a straight answer in under two minutes.

Which concrete services does Bel Covo offer in Farragut?

Our Farragut crews handle polished concrete, epoxy and polyaspartic coatings, decorative staining, driveways, patios, and repair work. Every job follows the same Pour-4-Polish process and finish discipline used on our flagship projects. The related links below point to the specific service pages that match common Farragut requests.

What questions come up most about Farragut concrete?

Do you take concrete projects in Farragut, Tennessee?

Yes. Farragut is inside our Knoxville coverage, about 18 miles west of Knoxville along Kingston Pike and I-40. We handle residential, commercial, and industrial concrete across Knox County, from custom-home garage coatings and driveways to polished interiors. Crews dispatch from our Knoxville team and book as scheduled mobilizations; travel costs show as a separate line on every quote.

What does a concrete driveway cost in Farragut?

Farragut driveways generally run $6.96 to $16.43 per square foot installed, depending on thickness, reinforcement, and finish. A two-car residential driveway (about 500 square feet) typically lands at $3,650 to $8,650. The online quote tool returns a project-specific number in about two minutes.

What does polished concrete cost for a Farragut custom home?

Residential polished concrete in Farragut runs $3.83 to $6.25 per square foot depending on sheen level and aggregate exposure. Salt-and-pepper Level 2 grinds start at the low end; a full-aggregate or scored decorative finish reaches the top. West Knox custom builds with a dyed or integrally pigmented spec sit at the top of that band.

Can you pour and coat a garage floor in the same scope?

Yes. Our Pour-4-Polish process handles the pour, the cure window, and the coating as one scope of work under our Knoxville team. One crew, one schedule, one warranty limited to our workmanship on the finished floor.

Last updated:

Ready to transform your floor?

Get a free, no-obligation quote for your project.