Skip to main content
Bel Covo
modern sleek onyx polished concrete

Concrete contractor in Lenoir City, TN

What does concrete flooring cost in Lenoir City, Tennessee?

Concrete flooring in Lenoir City runs the same ranges as the broader Tennessee market: polished concrete lands in the low-to-mid single digits per square foot, stained and decorative systems fall in the middle, and high-end epoxy or metallic builds reach the top of the range. Slab condition, square footage, and finish selection all move the real number. The regional breakdown below walks through what actually drives a Lenoir City quote up or down.

A lake town where I-75 meets US-321

Lenoir City sits where US-321 crosses Fort Loudoun Dam in Loudon County. I-75 and US-70 meet US-321 on the north side of town, and Fort Loudoun Lake lies to the west. As a concrete contractor in Lenoir City, TN, we split our work two ways: factory and trade floors along those roads, and lake and retirement homes like Tellico Village. The town sits about 25 miles southwest of our Knoxville team. Damp air off the water matters when we coat.

What does the lake-and-retirement economy mean for floor specs?

It means looks and a coating that lasts count for more than plain flatwork. Lake homes on Fort Loudoun Lake and Tellico Lake often pair outdoor living space with a garage floor that sees foot traffic from the boat launch and damp air off the water. A metallic or quartz finish for a show garage or a sunroom addition runs $6.08 to $10.17 a square foot.

Out back, a concrete patio with a standard 4-inch broom finish starts at $6.55 a square foot. An outdoor kitchen or a hot tub needs more. For those, we go to 5 inches thick with #4 rebar on 18-inch centers, and with that rebar a patio starts at $8.35 a square foot. That price covers a standard slab plus the rebar. The quote tool adds the extra thickness.

Waterfront properties: humidity matters at coating time

Slabs near Fort Loudoun Lake or Tellico Lake can hold extra moisture, mostly on low lots at or near the water table. When the slab's history or staining points to a moisture problem, we run a calcium chloride test before we pick a coating. It measures how much moisture comes up through the slab, so the spec fits your floor instead of a regional average.

What spec does the manufacturing strip along US-321 and I-75 require?

A commercial and light-industrial strip runs north along US-321 and next to the I-75 interchange. It’s shop slabs, warehouse floors, and distribution pads, where toughness counts more than looks. Forklift floors here start at a 6-inch slab with #4 rebar. With that rebar, a Loudon County shop slab starts at $7.04 a square foot. That covers a standard slab plus the rebar, and the quote tool adds the extra thickness. A resin floor for a wet or chemical area goes down a quarter inch thick. That one’s priced per job. The suppliers and subs behind those plants need commercial-grade concrete, too.

What stone does Loudon County concrete come from?

Loudon County sits in the Valley and Ridge region, on Ordovician Lenoir Limestone. It’s a knobby gray limestone named for this area, and it runs 25 to 500 feet thick across the county. Local ready-mix plants use crushed limestone from quarries around the Ridge-and-Valley belt. One is Vulcan Materials - Dixie Lee Quarry, about 6 miles away in Farragut. Three things follow from that:

  • Ground past 100 grit, Lenoir Limestone shows a warm, mixed color. That’s different from Memphis-area chert (cream to buff) or Nashville Basin limestone (a cooler gray-blue).
  • On hillside lots near the ridges, limestone can sit close to the surface. That adds digging and footing (footer) work to a slab or driveway quote.
  • If the stone look matters on a polished floor, we grind a test patch at no charge before we lock in the spec.

Driveway and patio installation, shop slabs, and garage floors in Loudon County

Homes around Lenoir City mix older in-town neighborhoods, newer builds along the lake, and rural acreage in the Loudon County interior. Driveway installation runs $6.96 to $16.43 a square foot, depending on the reinforcement and the finish, from broom to decorative. Polished concrete for a home runs $3.83 to $6.25 a square foot, from a salt-and-pepper look to full stone. Slab Boss Polish, our standard polish, starts at $3.58 a square foot on a home or a warehouse. The range above includes setup. A single rate can sit a little under it.

Shop and barn slabs use the same 6-inch rebar build as the shop floors along US-321. A Pour-4-Polish spec slab, poured to be polished, starts at $6.19 a square foot for the pour. The polish costs less when we pour and polish the slab as one job. See Pour-4-Polish for how that combined scope works and what it costs.

Garage epoxy and polyaspartic coatings are the most common ask in the lake and retirement market. Our standard polyaspartic garage floor in Loudon County is a two-coat flake system, with color flakes broadcast into the coating. On a sound slab, it runs $8.55 to $10.39 a square foot.

How does concrete work in Lenoir City get scheduled from the Knoxville team?

Lenoir City sits about 25 miles southwest of Knoxville, and our Knoxville team covers Loudon County as a routine run along US-321 and I-75. The drive cost shows on your quote as its own line, not folded into a per-foot rate. Our crews are typically 3 to 6 weeks booked. You get the price now. We set the date from there. The Tennessee locations page covers the rest of the East Tennessee cities our Knoxville team serves.

See what your Lenoir City floor costs

Enter your square footage and project details to see a full price in about 2 minutes.

What the concrete in Tennessee is actually made of

The aggregate story in West Tennessee concrete

Memphis and West Tennessee concrete uses Mississippi River chert gravel and sand from local pits. Crushed limestone comes in by rail or barge from Middle Tennessee (the Fort Payne Formation and the Mississippian limestone above it). West Tennessee has no hard-rock limestone quarry. Its bedrock sits under hundreds of feet of loose Coastal Plain sediment, so any coarse limestone in a Memphis slab has come 150 miles or more. Our Tennessee concrete flooring page covers where we work.

What gives Memphis polished floors their multi-toned cream look?

The river gravel is old Devonian and Mississippian chert, worn round over hundreds of miles of river. So the pebbles run gray, brown, red, cream, and black. No crushed-limestone area has that range. A polished floor reads as a warm cream to buff, peppered with tan, honey, gray, and reddish-brown pebbles. Ground and honed, it looks speckled, not one clean color. Darker gravel mixes lean toward a light khaki. A mix made with shipped-in limestone polishes closer to an even pale gray, the quieter choice.

Weathered chert can be porous, and it can react with cement and crack a slab from inside (alkali-silica reaction). Good producers screen for it. The loess bluffs (wind-blown silt) east of the river add silty sand to local mixes. That can raise how much water a hot-weather pour needs.

Local producers and cement

Memphis Stone and Gravel, part of Granite Construction, is the biggest local producer. It runs 3 sand and gravel mines in Mississippi River deposits and is building a fourth. Cement comes down the river by barge from Cape Girardeau and Festus, Missouri, to the Buzzi Unicem USA terminal at the Port of Memphis. No cement kiln runs in West Tennessee.

Does the river aggregate create problems for stain or coating finishes?

For stain, yes. Chert pebbles take acid stain poorly while the cement around them takes it well, so stained floors here come out mottled. A broom finish hides the gravel, though round gravel makes a tight cream harder to bring up. Polish shows the chert loud and clear. That’s character in a home or a small shop. On a big commercial floor meant to look even gray, it’s busy.

So pick by the look you want:

  • Speckled and many-toned: polish a river-gravel slab.
  • Even pale gray: ask for a limestone mix before the pour. An old slab keeps the look it has.
  • One even color on an existing slab: an epoxy coating over the ground slab covers the gravel.

What about Nashville, Knoxville, and Chattanooga?

Middle and East Tennessee have crushed stone quarries close to town: Rogers Group’s Whites Creek quarry in Nashville, Vulcan Materials’ Dixie Lee quarry in Farragut near Knoxville, and Martin Marietta and Vulcan quarries in Chattanooga. Our Nashville, Knoxville, and Chattanooga teams work that side of the state. A mix made with that crushed limestone polishes closer to an even pale gray than the river-gravel floors above.

What Does Concrete Work in Lenoir City Look Like?

Ground-level close-up of completed white vinyl chip epoxy floor showing chip texture and depth with service counter visible in distanceCompleted white vinyl chip epoxy floor in Ladd's showroom with worker in background and Club Car branding bannersCompleted white vinyl chip epoxy floor at Ladd's showroom looking toward service counter and green accent wallReflective brown polished concrete floor with fully exposed stone aggregate.Glossy brown polished concrete floor with exposed aggregate beside built in cabinets.full exposure polished concrete floor in a residential great room by Bel CovoPolished concrete floor in luxury home entryway reflecting chandelier and modern interior designAction Powersports custom logo embedded in glossy black epoxy showroom floorRound Barn polished concrete floor with mirror-like reflections of windows in dark high-gloss finishPolished charcoal concrete floors in open-plan luxury home with stone fireplace and floating staircasePolished dark concrete floor in restaurant bar area with branded bar stools, tap handles and TVsMetallic epoxy floor in dark amber and brown marble swirl pattern with mirror-like gloss finish

How far will Bel Covo travel to pour concrete in Lenoir City?

Bel Covo serves Lenoir City concrete projects within the standard service radius, and our crews are typically 3-6 weeks booked at any given moment. Every quote is itemized to show the cost of each step of the work, including the mobilization that gets equipment on site, so the quote doubles as the order of operations for your project. On accepted work, billing follows those same steps and shows the completion percentage of each as it happens, with nothing buried in a vague lump sum. Call 865-484-3528 for a straight answer in under two minutes.

Which concrete services does Bel Covo offer in Lenoir City?

Our Lenoir City crews handle polished concrete, epoxy and polyaspartic coatings, decorative staining, driveways, patios, and repair work. Every job follows the same Pour-4-Polish process and finish discipline used on our flagship projects. The related links below point to the specific service pages that match common Lenoir City requests.

What questions come up most about Lenoir City concrete?

Do you take concrete projects in Lenoir City, Tennessee?

Yes. Lenoir City is inside our Knoxville coverage, about 25 miles southwest of Knoxville along US-321. We do homes, commercial jobs, and flatwork across Loudon County, from lake-home driveways and garage coatings to shop slabs and polished floors. Crews dispatch from our Knoxville team and book as scheduled mobilizations. The drive cost shows as its own line on every quote before you say yes.

What does a concrete driveway cost in Lenoir City?

Lenoir City driveways are priced by the square foot, based on thickness, reinforcement, and finish. A two-car driveway, about 500 square feet, runs $3,650 to $8,650 before the drive cost. A slab that size runs above the per-foot range, since setup spreads over fewer feet. The online quote tool gives you a number for your project in about two minutes.

Can you pour and coat a garage floor in the same scope?

Yes. Our Pour-4-Polish process runs the pour, the cure time, and the finish coating as one scope of work under our Knoxville team. One spec, one schedule, and one warranty on our workmanship for the finished floor.

How does Loudon County's Lenoir Limestone bedrock affect a slab pour?

Loudon County sits on Ordovician Lenoir Limestone, a knobby gray limestone that makes good aggregate. Crushed limestone from Ridge-and-Valley quarries, including the Rogers Group Harriman Quarry in Roane County, feeds local ready-mix plants. It grinds to a warm, mixed color, unlike Nashville Basin or Memphis-area stone. Shallow rock on hillside lots can also add footing work, so we look at the site before we quote.

Last updated:

Ready to transform your floor?

Get a free, no-obligation quote for your project.