Skip to main content
Bel Covo
polished concrete luxury home entryway residence

Polished concrete cost in Tennessee (2026 pricing)

  • Concrete Craftsmen Since 2004
  • Statewide Tennessee Coverage
  • Slabs Built for the Finish
  • On-Site Moisture Testing

How much does polished concrete cost in Tennessee?

Polished concrete cost in Tennessee runs $3.83 to $6.25 per square foot with us. That range counts setup. The drive cost, our trip to your site, goes on top. The low end is our base polish, the standard 30 grit salt-and-pepper cut. The high end is a floor with every option on it. Where yours lands comes down to the shine you want, how much stone (aggregate) shows, and the shape of your slab.

The Tennessee polished concrete page walks through how we do the work. Whole floors at common sizes run like this, before the drive:

Project TypeTypical SizeSample FloorTotal Before the Drive
Warehouse / distribution5,000+ sf5,000 sf$18,400 to $30,150
Retail / restaurant1,000 to 5,000 sf2,500 sf$9,450 to $15,450
Residential or barndo500 to 3,000 sf1,500 sf$5,850 to $9,550

Bigger floors cost less per square foot. Hauling the machines, setting up, and rigging the dust shrouds cost about the same on an 1,800 square foot floor as on an 18,000 square foot one. On the big floor, that cost gets spread thin. A small floor runs above the per-foot range, since setup spreads over fewer feet. To get your own number, put your size and address in the quote tool and pick your options.

A warehouse grind-and-seal is the matte job, done at 400 to 800 grit. We price it per job, because its cost depends on how many passes the slab takes before we seal it. We want to see the floor first. For how Tennessee compares with the rest of the country, see our national guide to polished concrete prices.

Where do we work in Tennessee, and does it change the price?

The per-foot price comes off the same list anywhere in the state. What changes from place to place is the kind of job, the slabs, and the drive. Our Memphis team covers West Tennessee. That runs from the Delta east on I-40 to Jackson and Humboldt, north to Dyersburg and Ripley, and south into DeSoto County and Tunica. Our Nashville, Knoxville, and Chattanooga teams cover Middle and East Tennessee.

Polished concrete in Memphis and Shelby County

This covers Memphis, Collierville, Bartlett, Germantown, and Arlington. Two kinds of jobs fill the calendar here. Distribution buildings near the airport and across Shelby, Fayette, and DeSoto counties mostly want a grind-and-seal at 400 to 800 grit. Restaurants and shops in Midtown, Cooper-Young, and South Main usually go 1500 to 3000 grit. Homes are in the mix too, like our Chinquapin House polish in Collierville.

Downtown buildings from before 1980 are the ones to watch. A slab that old is a warning sign, so we run a calcium chloride moisture test (ASTM F1869) before any diamonds touch it.

Jackson, the I-40 corridor, and rural West Tennessee

This covers Jackson, Dyersburg, Brownsville, Covington, and Humboldt. Most of the work out here is barndominium floors across Madison, Chester, Henderson, Gibson, and Haywood counties. A barndo is a metal building you live in. Cheap acreage keeps barndo builds coming. Most owners settle on an 800 to 1500 grit floor inside. The work costs the same per square foot as in Memphis. The drive is longer, though, so the total runs a little higher.

FinishWhat It IsPer Square Foot
Warehouse grind-and-seal400 to 800 grit, then a sealer. Dries to a matte sheen.Priced per job
Standard polishOur base polish, the 30 grit salt-and-pepper cut. Fine sand and small stone show.From $3.58
Tighter, more even lookBase polish plus Grout and Cutback, a grout coat cut back to the slab$4.78, plus edges by the foot
Dyed floorBase polish plus dye$4.28
New barndo slabA Slab Boss Pour, then the polish at a lower field and edge ratePour from $5.55

These are floor-work prices. The range at the top includes setup. A single rate can sit a little under it. Scoring and acid stain are priced per job, once we see the floor.

Three things move a Tennessee price inside that range. First is the kind of job. Memphis stores and restaurants run 800 to 3000 grit. Distribution slabs along I-40 run 400 to 800 grit. Madison and Tipton County barndo floors usually settle at 800 to 1500 grit. Second is what shows up at the grinder. Older Downtown Memphis and South Main buildings often carry VCT glue, acrylic curing compound, and moisture nobody ever measured. Newer Shelby and Fayette County warehouse slabs grind clean. Third is the drive on small jobs. Bartlett (15 miles), Collierville (28 miles), and Covington (40 miles) sit closest to Memphis. And the Mid-South air runs around 70 percent humidity all summer, which shapes the prep more than the polish.

How do the polish options work?

The shape of your slab the morning we start sets most of the labor hours. It also sets how fast we wear out diamonds. Every Tennessee floor we polish is a Slab Boss Polish. The only question is which of the two options you add.

What comes with the base build?

The base build is the full polish on any existing slab, no matter who poured it or what shape it’s in. We grind, hone, put down one coat of hardener (densifier), and polish. It starts at $3.58 a square foot for the floor work. Some slabs take extra diamond passes: an unknown mix, acrylic curing compound left on top, and old VCT glue all add them. So does a floor less flat than an FF of 25 under ACI 117. FF is the flatness number you’ll see on bids, and higher is flatter.

What do the two options add?

Each option builds a better floor, and each one is its own line per square foot in the quote calculator.

LineWhat You GetWho Can Get ItPer Square Foot
Slab Boss Polish, baseGrind, hone, one hardener coat, polishAny slabFrom $3.58
Grout and CutbackA thin cement grout fills pores and small holes in the field. Then we cut the extra back to the slab, so the floor reads tighter and more even.After we look at the slabAdd $1.20, plus $1.63 a foot of edge
Double-Pass DensificationA second hardener coat on top of the one that comes standard. It hones tighter and holds more gloss.After we look at the slabAdd $0.40
Both optionsBase polish with every option onAfter we look at the slab$5.18
Paired with a SPEC pourWe pour the slab too, through Pour-4-PolishA Bel Covo pourField and edge polishing about 30% lower

Your price is the base plus each option you pick. Not every slab can take every option, so we look at yours first.

Polish at about a 30% lower rate with a SPEC pour

With Pour-4-Polish, we pour a SPEC-built Slab Boss Pour under the whole polished area. It goes on the same quote as the Slab Boss Polish. Then the field and edge polishing get the lower rate. We write the pour spec for the polish. So the slab shows up flat, dense, and evenly cured, ready for every option.

What drives your final price?

Five things decide where your Tennessee floor settles in the range.

1. Slab condition. This is the biggest one. Curing compound left on top, tile glue (mastic), or a floor less flat than an FF of 25 each add diamond passes. Pre-1980 slabs in Downtown Memphis and South Main often land in the heavy-prep group.

2. Grind level. The 30 grit cut that gives you salt and pepper is in the base price. A deeper cut toward full stone is billed by the crew hour. A true cream polish is rare, because it needs a very flat slab. The cut depth guide lays out all three cuts.

3. Square footage. The price per square foot eases off past 2,000 square feet, then again past 5,000, as the setup spreads over more floor.

4. Options you add. Each one is a line in the options table.

5. Site prep. Structural crack work, polyurea joint fill, a moisture fix, and old coating removal each get their own line on top of the base polish. Taking up the black glue under a 20-year-old VCT floor is priced per job, after we see how thick it is.

How far is Memphis from your address, and what does that add?

The drive is its own line on your quote. The quote tool figures it from the real distance to your address, so you never have to guess. Here’s how far common towns sit from Memphis, one way.

Project CityOne-Way Distance
Memphis, Bartlett, Germantown0 to 15 miles
Collierville, Arlington20 to 30 miles
Covington, Brownsville40 to 55 miles
Jackson, Humboldt80 to 90 miles
Dyersburg, Ripley75 to 90 miles

Small jobs on the far edge of West Tennessee

A small floor, under 1,500 square feet and more than 90 miles from Memphis, is hard to price fairly as a trip of its own. We try to line it up with another job in the same county that week. Tell us your dates can flex when you send your project, and we'll look for a match.

What does a Tennessee polish quote include?

A Bel Covo quote for polishing concrete in Tennessee covers the diamond grinding through every grit we spec. For high gloss, that’s 50, 100, 200, 400, 800, 1500, and 3000. It also covers the lithium silicate hardener, the final guard coat, and a walk over the slab before the first pass. Joint and crack repair follows ICRI guidance. The drive to your address is in there. So is HEPA-shroud dust control, which matters most in a busy Midtown or Cooper-Young block. If that walk turns up old stains, a failed finish, or a slab nobody can date, we add a calcium chloride test (ASTM F1869). You can ask for one on any job, too. The quote leaves out structural crack work and a moisture primer when the test reads high. It also leaves out removing old coatings or glue, moving furniture, and the new pour itself. Building a barndo along I-40? The Tennessee barndominium polished concrete page covers pouring and polishing on one quote.

How does polished concrete compare to other Tennessee floors?

Floor TypeUpfront per sfUpkeep
Polished concrete$3.83 to $6.25Guard coat once a year, never a recoat
Epoxy coating (100% solids)$6.08 to $10.17Recoat every 5 to 12 years
Stained concrete$2.19 to $6.29Reseal every 2 to 4 years
VCT tile$4 to $8[1]Strip and wax every year
Commercial carpetNot our work; ask the flooring storeReplace every 5 to 7 years

The yearly guard coat on a polished floor runs $0.72 a square foot, plus setup and the drive. It’s a coat and a buff you can schedule, not a tear-out. VCT needs a strip and wax every year, and carpet comes up and goes back down every 5 to 7 years. Epoxy wears faster under forklift wheels, and each recoat means grinding and coating again.

How to get a Tennessee quote

Start with the online quote calculator. Put in your Tennessee city, your square footage, the finish you want, and anything you know about the slab’s age or old coatings. It hands back a line for each part. That’s the diamond passes, the hardener, the final guard coat, the drive, and any prep your slab needs. It takes about 2 minutes.

See what your Tennessee polished concrete costs

Enter your square footage and project address. The tool prices the work and the drive together and hands you one real number instead of a wide range.

Why does one Tennessee quote look cheaper than another?

Grind level. A rock-bottom “polished” price from another contractor often means a 200 grit honed floor. Below 800 grit, it’s a hone, not a polish.

Hardener. Lithium silicate holds up to wear longer than sodium or potassium silicate. That matters in any building with forklift traffic.

Pass count. A real high-gloss floor needs 7 to 9 passes, each with a finer diamond. Shortcut bids run 4 to 5 passes, and the swirl marks show up later under LED store lights.

Honest prep. A pre-1980 slab in Downtown Memphis or South Main should come with a written prep plan and a moisture reading behind it, not a spoken promise.

Where these market figures come from

Every price on this page that is not ours is listed here. Our own rates carry no number: they link straight into the quote tool.

  1. Vinyl composition tile, installed: $4 to $8 per SF. Bel Covo market survey, retrieved 2026-08-12. Installed commercial VCT price a coated garage floor is compared against, carried over from figures already published across our cost pages; pending third-party re-verification.

Pricing in Tennessee

In Tennessee, most projects range from $3.83 to $6.25 per square foot. Final cost depends on floor condition, area size, and finish selection.

Get your custom quote

See the results

Ground-level close-up of completed white vinyl chip epoxy floor showing chip texture and depth with service counter visible in distanceCompleted white vinyl chip epoxy floor in Ladd's showroom with worker in background and Club Car branding bannersCompleted white vinyl chip epoxy floor at Ladd's showroom looking toward service counter and green accent wallReflective brown polished concrete floor with fully exposed stone aggregate.Glossy brown polished concrete floor with exposed aggregate beside built in cabinets.full exposure polished concrete floor in a residential great room by Bel CovoHigh-gloss sealed outdoor concrete slab with mirror-like reflection of a boat trailer in daytimePolished concrete floor in Westmoore Community Church lobby viewed from wider angleReflective polished concrete foyer floor under construction showing mirror finish and window reflectionsClark Crew BBQ dining room with polished concrete floor and rustic branding elementsClose-up of polished concrete showing heavy aggregate exposure with mirror-like sheenMirror-finish black polished concrete floor in SLIM clothing boutique

Frequently asked questions

How much does polished concrete cost per square foot in Tennessee?

With us, polished concrete in Tennessee runs $3.83 to $6.25 a square foot, and that range counts setup. The low end is our base polish, the standard 30 grit salt-and-pepper cut that shows fine sand and small stone. The high end has both options on: a grout coat that fills the pores and gets cut back to the slab, and a second coat of hardener. A warehouse grind-and-seal at 400 to 800 grit is priced per job, because it depends on how many passes the slab takes before we seal it. Dye and scoring go on top. The per-foot list is the same in Memphis and in rural West Tennessee. What changes is the drive cost, our trip to your site, so a Madison County barndo floor can total a bit more than a Shelby County floor the same size. Work in a busy Midtown block can run higher too, because it needs dust control and night hours.

Why does polished concrete cost more for some Tennessee projects than others?

Three things move it: the shine, how much stone shows, and the shape of the slab when we start. A 400 to 800 grit grind-and-seal for an I-40 warehouse takes fewer passes and dries to a matte sheen, so it costs less a foot. A 1500 to 3000 grit polish for a Midtown restaurant or an East Memphis store takes more passes with finer diamonds and ends close to a mirror. Our standard cut shows fine sand and small stone and is in the base price. Cutting deeper toward full stone adds passes, and cream polish, with no stone showing, is rare and needs a very flat slab. The slab is the wild card in Memphis. Many Downtown and South Main buildings from before 1980 have no modern vapor barrier, the plastic sheet under a slab that blocks ground water. They often carry old tile glue or curing compound on top too, and that can take two to four extra grinding passes before the polish even starts.

What is included in a Bel Covo polished concrete quote in Tennessee?

A standard Tennessee polish quote covers diamond grinding through the grits we spec, a lithium silicate hardener (densifier), a final guard coat, and a look at the slab before we grind. It also covers standard crack and joint repair, hauling the machines and crew to your site, dust control with HEPA-filtered shrouds, and cleanup. We check every slab. If the check turns up a warning sign, like a pre-1980 building or a low lot near the river, we add a calcium chloride moisture test (ASTM F1869), and you can ask for one on any job. The quote leaves out structural crack repair, and a moisture barrier primer when the slab reads above 3 pounds on that test. It also leaves out removing old epoxy, tile glue, or paint, any acid stain, moving furniture or equipment, and the slab itself on new construction. Each of those gets its own line, so the base number stays honest. When we pour the slab through Pour-4-Polish, the field and edge polishing get a lower rate, because we wrote the pour spec for the polish.

Does travel distance affect the Tennessee polished concrete price?

Yes. Our Memphis team takes polished concrete jobs across West Tennessee, and the drive is its own line on your quote. The online quote tool figures it from your project address, so you see it before you send anything. Collierville sits about 28 miles from Memphis. Dyersburg is about 82 miles out, and Jackson about 85. Middle and East Tennessee jobs go to our Nashville, Knoxville, and Chattanooga teams, and the quote tool sends yours to the nearest one.

How does Tennessee polished concrete pricing compare to other flooring options?

Up front, polished concrete runs $3.83 to $6.25 a square foot with us. Epoxy runs $6.08 to $10.17, and stained concrete runs $2.19 to $6.29. Upkeep is where they split. A polished floor never needs a recoat; it gets a fresh guard coat and a buff about once a year, at $0.72 a square foot plus setup and the drive. Epoxy needs a recoat every 5 to 12 years and wears faster under hard forklift wheels. Stained concrete holds up to wear less well than polish. Memphis averages above 70 percent relative humidity (per NWS Memphis climate summaries). Carpet there usually gets replaced every 5 to 7 years, and it can grow mold along the slab edges in older South Main and Crosstown buildings.

Last updated:

Ready to transform your floor?

Get a free, no-obligation quote from our team.