Skip to main content
Bel Covo
modern sleek onyx polished concrete

Concrete contractor in Selmer, TN

What does concrete flooring cost in Selmer, Tennessee?

Concrete flooring in Selmer runs the same ranges as the broader Tennessee market: polished concrete lands in the low-to-mid single digits per square foot, stained and decorative systems fall in the middle, and high-end epoxy or metallic builds reach the top of the range. Slab condition, square footage, and finish selection all move the real number. The regional breakdown below walks through what actually drives a Selmer quote up or down.

Concrete work on McNairy County loess

Selmer sits about 67 miles north of our North Mississippi team, along US-78 and US-45, and McNairy County is regular work for us. As a concrete contractor in Selmer, TN, we build on loess, a fine silt that settles if it isn’t packed right. So every pour starts with a pack test. Get your price in 2 minutes.

Selmer sits in the middle of McNairy County’s working-building trade: retail slabs along US-45, pours on the county’s industrial parcels, and a steady run of shop and barn slabs on rural land. We pour and finish shop slabs, barndominium floors, coated garages, and polished concrete here. You get one contact from the pour to the finish, and no handoff to a second contractor.

McNairy County subgrade and slab preparation

Most of the ground under McNairy County is loess silt over older Mississippi River chert gravel. The loess is the part that varies. It compresses slowly under weight when nobody packs it before the pour. A slab on loose loess settles unevenly, and that movement shows through any coating or polish put on later.

An existing slab that’s getting a coating or a polished finish is a different job. We look for signs of moisture first, and we test when we find them, before we pick a coating. Loess holds water longer than sandy soil does. And water vapor pushing up through the slab is the main reason bonded coatings fail around here.

What stone and aggregate go into a Selmer slab?

Crushed stone for McNairy County pours comes mostly from APAC-Mississippi’s Corinth plant, in Alcorn County, Mississippi. Sand and gravel come from Memphis Stone and Gravel, which digs river-run chert from the Mississippi River gravel beds to the west. That mix is heavy on chert, with pebbles in many colors. It gives a polished slab here a warm cream-to-buff finish, not the cooler gray you get from sand that’s mostly quartz. Want an even gray polished floor? Then a self-leveling overlay over the new pour is the cleaner way to get it.

The chert in this supply carries a moderate risk of alkali-silica reaction (ASR). That’s when the rock reacts with the cement and slowly cracks the concrete from inside, and it matters most on a polished floor you plan to keep a long time. So on structural pours, we swap part of the cement for Class F fly ash as a standard step.

One spec for pour and finish

Our Pour-4-Polish process books the pour and the coating or polish as one scope. We write the pour spec for the finish that goes on it, so one spec and one workmanship warranty on the completed install cover the whole floor. Polished concrete flooring and garage coatings in Selmer both qualify.

What concrete services does Bel Covo build on Selmer ground?

Shop and barn slabs. Working buildings in McNairy County carry more weight than a home garage, and many get a coating or polish later. We pour at 4,000 PSI or stronger, add steel sized to the load, and thicken the edges under the overhead doors. Any floor that will get a finish later gets a vapor barrier under it. Shop slab details

Driveways and approaches. On loess, packing the base is the prep, not a step to rush. Our standard driveway quote is a 5 inch slab on a packed gravel base, with rebar, poured with a 4,500 PSI mix. On any bid, 4,000 PSI is the least to accept. We cut control joints spaced to the slab’s thickness. Driveway details

Garage floor coatings. We diamond-grind the surface open, then lay the coating. Most home garages take a chip-broadcast floor. Shops with chemical spills get a polyaspartic topcoat instead. Garage coatings

Polished concrete. Barndominium interiors and commercial floors get polished to 800 grit or finer, right in the slab. The shine is part of the concrete, not a topcoat that peels. Polished concrete

Patios and flatwork. Patios get the same loess prep as a driveway, with their own finish choices. Patio details

See what your Selmer floor costs online

Answer a few questions about your project and get a ballpark price. No callback wait, no waiting on an estimator visit.

How much does concrete cost for a Selmer driveway, coating, or polish?

A new driveway runs $6.96 to $16.43 a square foot installed. A two-car drive of about 500 square feet runs $3,650 to $8,650 before travel. That’s a little above the per-foot range, since setup spreads over fewer feet.

A coating on an existing slab runs $8.55 to $10.39 a square foot. Polish runs $3.83 to $6.25 a square foot, and the grit level moves it. On a new slab, the pour is priced on top. The quote tool turns your square footage and project type into a ballpark. Travel from our North Mississippi team to Selmer shows as its own line on every quote, so you see it before you commit, not after.

Other McNairy County cities Bel Covo serves

Our North Mississippi team also covers Adamsville, Bethel Springs, Eastview, and Michie, and the Tennessee service area lists every town we cover.

What the concrete in Tennessee is actually made of

The aggregate story in West Tennessee concrete

Memphis and West Tennessee concrete uses Mississippi River chert gravel and sand from local pits. Crushed limestone comes in by rail or barge from Middle Tennessee (the Fort Payne Formation and the Mississippian limestone above it). West Tennessee has no hard-rock limestone quarry. Its bedrock sits under hundreds of feet of loose Coastal Plain sediment, so any coarse limestone in a Memphis slab has come 150 miles or more. Our Tennessee concrete flooring page covers where we work.

What gives Memphis polished floors their multi-toned cream look?

The river gravel is old Devonian and Mississippian chert, worn round over hundreds of miles of river. So the pebbles run gray, brown, red, cream, and black. No crushed-limestone area has that range. A polished floor reads as a warm cream to buff, peppered with tan, honey, gray, and reddish-brown pebbles. Ground and honed, it looks speckled, not one clean color. Darker gravel mixes lean toward a light khaki. A mix made with shipped-in limestone polishes closer to an even pale gray, the quieter choice.

Weathered chert can be porous, and it can react with cement and crack a slab from inside (alkali-silica reaction). Good producers screen for it. The loess bluffs (wind-blown silt) east of the river add silty sand to local mixes. That can raise how much water a hot-weather pour needs.

Local producers and cement

Memphis Stone and Gravel, part of Granite Construction, is the biggest local producer. It runs 3 sand and gravel mines in Mississippi River deposits and is building a fourth. Cement comes down the river by barge from Cape Girardeau and Festus, Missouri, to the Buzzi Unicem USA terminal at the Port of Memphis. No cement kiln runs in West Tennessee.

Does the river aggregate create problems for stain or coating finishes?

For stain, yes. Chert pebbles take acid stain poorly while the cement around them takes it well, so stained floors here come out mottled. A broom finish hides the gravel, though round gravel makes a tight cream harder to bring up. Polish shows the chert loud and clear. That’s character in a home or a small shop. On a big commercial floor meant to look even gray, it’s busy.

So pick by the look you want:

  • Speckled and many-toned: polish a river-gravel slab.
  • Even pale gray: ask for a limestone mix before the pour. An old slab keeps the look it has.
  • One even color on an existing slab: an epoxy coating over the ground slab covers the gravel.

What about Nashville, Knoxville, and Chattanooga?

Middle and East Tennessee have crushed stone quarries close to town: Rogers Group’s Whites Creek quarry in Nashville, Vulcan Materials’ Dixie Lee quarry in Farragut near Knoxville, and Martin Marietta and Vulcan quarries in Chattanooga. Our Nashville, Knoxville, and Chattanooga teams work that side of the state. A mix made with that crushed limestone polishes closer to an even pale gray than the river-gravel floors above.

What Does Concrete Work in Selmer Look Like?

Ground-level close-up of completed white vinyl chip epoxy floor showing chip texture and depth with service counter visible in distanceCompleted white vinyl chip epoxy floor in Ladd's showroom with worker in background and Club Car branding bannersCompleted white vinyl chip epoxy floor at Ladd's showroom looking toward service counter and green accent wallReflective brown polished concrete floor with fully exposed stone aggregate.Glossy brown polished concrete floor with exposed aggregate beside built in cabinets.full exposure polished concrete floor in a residential great room by Bel CovoPolished concrete floor in luxury home entryway reflecting chandelier and modern interior designAction Powersports custom logo embedded in glossy black epoxy showroom floorRound Barn polished concrete floor with mirror-like reflections of windows in dark high-gloss finishPolished charcoal concrete floors in open-plan luxury home with stone fireplace and floating staircasePolished dark concrete floor in restaurant bar area with branded bar stools, tap handles and TVsMetallic epoxy floor in dark amber and brown marble swirl pattern with mirror-like gloss finish

How far will Bel Covo travel to pour concrete in Selmer?

Bel Covo serves Selmer concrete projects within the standard service radius, and our crews are typically 3-6 weeks booked at any given moment. Every quote is itemized to show the cost of each step of the work, including the mobilization that gets equipment on site, so the quote doubles as the order of operations for your project. On accepted work, billing follows those same steps and shows the completion percentage of each as it happens, with nothing buried in a vague lump sum. Call 662-356-3528 for a straight answer in under two minutes.

Which concrete services does Bel Covo offer in Selmer?

Our Selmer crews handle polished concrete, epoxy and polyaspartic coatings, decorative staining, driveways, patios, and repair work. Every job follows the same Pour-4-Polish process and finish discipline used on our flagship projects. The related links below point to the specific service pages that match common Selmer requests.

What questions come up most about Selmer concrete?

Does Bel Covo serve Selmer and McNairy County directly?

Yes. Selmer sits about 67 miles north of our North Mississippi team, and McNairy County is part of the area that team covers. We pour driveways and shop slabs, and we put down garage coatings and polished concrete for McNairy County properties. Travel shows as its own line on the quote before you commit.

What does a concrete driveway cost in Selmer, Tennessee?

Selmer driveways run $6.96 to $16.43 a square foot installed, set by thickness, steel, and finish. A two-car drive of about 500 square feet runs $3,650 to $8,650 before travel. A drive that small prices a little above the per-foot range, since setup spreads over fewer feet. The online quote tool prices your own drive.

What aggregate goes into concrete poured in McNairy County?

Crushed stone comes from APAC-Mississippi in Corinth, and river-run sand and gravel come from Memphis Stone and Gravel. The mix is heavy on chert, and it polishes to a warm cream-to-buff finish. On structural pours, we swap part of the cement for Class F fly ash to keep alkali-silica reaction in check.

Is the loess subgrade in McNairy County a problem for slabs?

It can be. Loess compresses under weight when it isn't packed, so every Selmer pour starts with a check that the base is packed. On an existing slab going to a coating or polish, we look for signs of moisture first and test when we find them. Loess holds water longer than sandy soil, and water vapor is the main reason coatings fail here.

Last updated:

Ready to transform your floor?

Get a free, no-obligation quote for your project.

McNairy County, Tennessee

See concrete work across McNairy County, Tennessee →